JVC XL-R2010BK - Manual (Page 35)

33
Engli
s
h
4
Press the SET button (main unit/remote
control).
• “ERASE (start track) – (last track)?” is flashed in the informa-
tion display. (Initially, the start track and last track are both the
last track number recorded on the CD-RW.)
• Press the CANCEL button (main unit/remote control) if you do
not wish to perform this procedure.
5
If needed, use the MULTI JOG control or press
the
2 / 3 (menu) button on the remote control to
select the number of tracks you want to erase
preceding the last track.
• Please note that all tracks following the start track will be
erased. For example, when track 8 on an 11 track CD-RW is
assigned as the start track, tracks 8, 9, 10, and 11 will be erased.
6
Press the SET button (main unit/remote
control).
• “ERASE TRACK” is flashed in the information display, the
selected tracks are erased, and the normal display is shown
when erasing has been completed.
• Each track that was erased is cleared from the music calendar.
• Tracks can only be erased starting from the last track recorded
on a disc.
Notes
•
Once a track is erased, the recording cannot be restored.
• Do not turn the power off, disconnect the AC power cord from
the wall outlet or subject the unit to vibration during the erase
operation. Doing so may ruin the CD-RW disc.
The Disc Erase function is used to erase the entire contents of the
CD-RW. This unit uses a unique high-speed (2x) erasing function
that is different from normal erasure procedures. Erasing is per-
formed all the way through the disc’s TOC (Table of Contents).
“ERASE DISC” flashes in the information display during the eras-
ing process.
Note
•
You cannot perform other operations with the unit while
“ERASE DISC” is flashing.
*Please refer to the Glossary for a brief definition of acronyms.
(see page 41)
Caution
If the disc is damaged or there is disc related trouble, this function
may not be possible.
1
Load the CD-RW to be erased in the CDR disc
tray.
• The number of tracks and play time are shown in the informa-
tion display.
2
When the unit is in the stop mode, press the
MENU button (main unit/remote control).
3
Turn the MULTI JOG control or press the 2 / 3
(menu) button on the remote control until “DISC
ERASE” is shown in the information display.
4
Press the SET button (main unit/remote
control).
• “ERASE DISC?” is shown in the information display.
• Press the CANCEL button (main unit/remote control) if you do
not wish to perform this procedure.
5
Press the SET button (main unit/remote
control).
• Full disc erasure takes a few minutes to perform. During the
procedure, the length of the level meter is used to indicate
approximately how much time is remaining until erasure is
complete (One segment equals approximately 15 seconds).
“ERASE DISC” flashes on the information display. When the
disc has been erased, “BLANK DISC” is displayed, then
changes to “CDR 1 0:00.”
Erasing All Tracks (Disc Erase
Function) (CD-RW only)
STANDBY
STANDBY/ON
MAX MIN
LEVEL PHONES
PLAY MODE CD EDIT
REC SOURCE SELECTOR
CD REC
STOP PLAY PAUSE
REC SOURCE DIGITAL CD LINE MIC OPEN/CLOSE OPEN/CLOSE
XL-R2010 CD/CDR MULTIPLE COMPACT DISC RECORDER
CANCEL SET MENU
PAUSE REC/REC MUTING PLAY STOP
SYNCHRO
FINALIZE
MULTI JOG/REC LEVEL
+ –
MIX BLANCE CD LINE LINE MIC
MIC
4,5
3
2
1
CANCEL
STANDBY/ON
CD REC
PLAY MODE
• REC
REC MUTING
REC SOURCE MENU
PITCH 0 CHA NCE L
REPEAT CD
PITCH +
SET
PITCH–
RM–SXLR2010A REMOTE CONTROL
CDR
CD EDIT FINALIZE DISPLAY
1 2
4 5
7 8
3
6
9
10 +10
FADE SYNCHRO
C O N T R O L
3
4,5
2
CANCEL
Eng.book Page 33 Monday, May 28, 2001 9:46 AM