JVC HM-DR10000EU - Manual (Page 54)

54
EN
MODE SET
B. E. S. T. ON
PICTURE CONTROL AUTO
AUTO TIMER OFF
O. S. D. ON
DIRECT REC ON
AUTO SP =LP TIMER OFF
DIGITAL 3R ON
NEXT PAGE
[ 5∞] =
[MENU] : EXIT
AV2 SELECT Setting
Set "AV2 SELECT" to the appropriate mode depending on the type of unit connected to the rear panel AV2 IN/DECODER
connector of this recorder.
1 Press MENU to access the Main Menu screen.
2 Press %fi to move the highlight bar (pointer) to "MODE SET", then press OK or #
.
3 Press %fi to move the highlight bar (pointer) to "AV2 SELECT".
4 Press OK or
#
to select "AV2", "DECODER" or "SAT".
a–AV2 : To use this recorder as the recording deck with the player connected to the
AV2 IN/DECODER connector, or to use the satellite tuner connected to the
AV2 IN/DECODER connector.
b–DECODER : To use a decoder connected to the AV2 IN/DECODER connector.
c–SAT
: To view a satellite programme with the TV set while the recorder is in Timer
mode, in Stop mode, recording or turned off. (
੬
pg. 57)
5 Press MENU to return to normal screen.
● If you have a decoder connected to the AV2 IN/DECODER connector, be sure to set "AV2
SELECT" back to "DECODER" after editing.
● If you're not connecting a decoder to the AV2 IN/DECODER connector, leave "AV2 SELECT"
set to "AV2".
● The default setting is "AV2"; if the recorder's memory backup has expired due to a power cut
or because the AC was removed from the recorder, "AV2" will be automatically selected when
the power is restored to the recorder. If you are using a decoder, be sure to set "AV2 SELECT"
back to "DECODER".
● If the AV1 OUT switch on the rear panel is set to Y/C, it is impossible to set "AV2 SELECT" to
"DECODER".
EDITING (cont.)
PREVIOUS PAGE
POWER SAVE
OFF
S-VHS AUTO
AV1 SELECT VIDEO
AV2 SELECT AV2
COLOUR SYSTEM PAL/NTSC
DV SOUND
SOUND1
AUDIO REC NICAM
[ 5∞] =
[MENU] : EXIT
MODE SET
B. E. S. T. ON
PICTURE CONTROL AUTO
AUTO TIMER OFF
O. S. D. ON
DIRECT REC ON
AUTO SP =LP TIMER OFF
DIGITAL 3R ON
NEXT PAGE
[ 5∞] =
[MENU] : EXIT
AV1 SELECT Setting
Set "AV1 SELECT" to the appropriate mode depending on the type of unit connected to the rear panel AV1 IN/OUT connector of
this recorder.
1 Press MENU to access the Main Menu screen.
2 Press %fi to move the highlight bar (pointer) to "MODE SET", then press OK or #
.
3 Press %fi to move the highlight bar (pointer) to "AV1 SELECT".
4 Press OK or
#
to select "VIDEO" or "S-VIDEO".
a–VIDEO : If a connected device's output is compatible only with regular video signals,
set "AV1 SELECT" to "VIDEO".
b–S-VIDEO : If a connected device's output is compatible with Y/C signals, set "AV1
SELECT" to "S-VIDEO". This setting will let you take advantage of higher-
quality S-VHS pictures.
5 Press MENU to return to normal screen.
● If "AV2 SELECT" is set to "DECODER", it is impossible to set "AV1 SELECT" to "S-VIDEO".
PREVIOUS PAGE
POWER SAVE
OFF
S-VHS AUTO
AV1 SELECT VIDEO
AV2 SELECT AV2
COLOUR SYSTEM PAL/NTSC
DV SOUND
SOUND1
AUDIO REC NICAM
[ 5∞] =
[MENU] : EXIT