SUPER MICRO Computer SUPER X8STE - Manual (Page 55)

Chapter 2: Installation
2-31
BMC JTAG
1
SAS1 SAS2
SAS7 SAS3
SAS4 SAS5 SAS6
JWOL
Battery
JD1 SPKR1
JAR
JI2C1 JI2C2
JPS2
JL1
1
JOH
1
JF1
LES1
LE1
COM1
FAN4
FAN3
FAN5
FAN2
FAN1
JPW1 SMBUS_PS1 JPW2
JPG1
JPUSB3
JBMC1 JPS1
JPUSB2
JPL1
JPL2
JLED
JWD
JPUSB1
IPMI_LAN
COM2 Floppy
I-Button
T-SGPIO1
3-SGPIO2
3-SGPIO1
USB 6/7
USB 4/5
USB3 USB2
Slot6 PCI-E 2.0 X8 on X16
Slot3 PCI-E 2.0 X8
I-SA
TA4
I-SA
TA5
Slot4 PCI-E 2.0 X4 on X8
Slot2 PCI 33MHz
Slot5 PCI-E 2.0 X8
I-SA
TA2
I-SA
TA3
DIMM1B
DIMM1A
DIMM3B
DIMM2B
DIMM2A
DIMM3A
I-SA
TA0
I-SA
TA1
X8ST3-F/X8STE
USB 0/1
LAN2
LAN1
VGA
KB/MOUSE
BIOS
JBT1
Slot1 PCI 33MHz SAS0
T-SGPIO2
LAN CTRL
for IPMIl LAN
LAN
CTRL1
LAN
CTRL2
SI/O
BMC CTRL
BMC
Firmware
SAS CTRL
Intel ICH10R
South Bridge
Intel X58-Express
North Bridge Intel Processor
LES2
LSI 1068E
WPCM 450
CPU FAN
A
A. BP USB 0/1 Wake-up
B. FP USB 4/5, 6/7 Wake-up
C. FP USB 2, 3 Wake-up
USB Wake-Up
Use JPUSB jumpers to "wake-up" your sys-
tem by pressing a key on a USB keyboard or
clicking the USB mouse of your system. The
JPUSB jumpers are used together with the
USB Wake-Up feature in the BIOS. Enable
both USB jumpers and the USB feature in
the BIOS to wake-up your system via USB
devices. See the table on the right for jumper
settings and jumper connections.
Note: JPUSB1 is used for Backpanel
USB ports #0/1, JPUSB2 is for Front
Panel USB ports #4/5, and #6/7.
JPUSB3 is used for Front Accessible
USB Ports 2 and 3. When the USB func-
tion is set to Enabled in the BIOS, and a
USB Wake-up jumper is set to Disabled,
be sure to remove the USB devices
from the USB ports whose USB jumper
is Disabled before the system goes into
the standby mode. (The default setting
is
Enabled.)
JPUSB1 (BackPanel USB
0/1 Wake-up Enable)
Pin# Definition
1-2 Enabled (Default)
2-3 Disabled
JPUSB2 (Front Panel USB
4/5, 6/7 Wake-up Enable)
Pin# Definition
1-2 Enabled (Default)
2-3 Disabled
B
C
JPUSB3 (Front Panel USB
2, 3 Wake-up Enable)
Pin# Definition
1-2 Enabled (Default)
2-3 Disabled