Sony MVS8000SF-C - Manual (Page 50)

1-42
MVS-8000SF
<Switch>
S100 (A-3) : OUT-CPU RESET switch
Pressing this switch initializes the CPU on the OUT-23/24
board.
S1501 (A-7) : MONITOR reset switch
The reset switch that is used to reset the monitor during
maintenance through the terminal.
<Connector>
CN1400 (A-5) : ISP common connector
Used only for production in the assembly factory. Used for
program writing into the JTAG device with ISP.
CN1502 (A-8) : TERMINAL pin
This pin is connected to the control terminal and used
during maintenance.
<TEST terminal>
E102 (E-7), E103 (H-6), E104 (J-12), E105 (P-13),
E107 (P-6) : GND terminal (OUT-23 board)
Use this terminal as the earth point for measuring the
respective check terminals.
E103 (J-6), E104 (K-13), E105 (P-13), E107 (P-5),
E109 (D-13), E108 (J-1), E1010 (P-1) : GND
terminal (OUT-24 board)
Use this terminal as the earth point for measuring the
respective check terminals.
TP101 (A-3) : + + + + +12 V check terminal
+12 V measuring terminal.
TP102 (A-4) : + + + + +5 V check terminal
+5 V measuring terminal.
TP103 (A-4) : + + + + +3.3 V check terminal
+3.3 V measuring terminal.
TP104 (A-4) : + + + + +2.5 V check terminal (OUT-23 board)
+2.5 V measuring terminal.
TP104 (A-5) : + + + + +2.5 V (OUT-24 board)
+2.5 V measuring terminal.
TP201 (P-13) : VD (vertical sync) signal check terminal
VD signal measuring terminal.
TP202 (P-12) : CKX (control timing) signal check terminal
CKX signal measuring terminal.
TP203 (N-12) : HD (horizontal sync) signal check
terminal (OUT-23 board)
HD signal measuring terminal.
TP204 (N-13) : FLOE (field odd even) signal check
terminal
FLOE signal measuring terminal.
TP203 (P-12) : HD (horizontal sync) signal check
terminal (OUT-24 board)
HD signal measuring terminal.
TP204 (P-12) : FLOE (Field Odd Even) signal
check terminal
FLOE signal measuring terminal.
TP205 (J-13), TP206 (J-7) : CK (clock for video)
signal check terminal (OUT-23 board)
Uses this terminal when checking the clock signal for video.
TP205 (J-13), TP206 (J-6) : EAV_C signal check
terminal (OUT-24 board)
CLOCK signal measuring terminal.
TP207 (K-7) : VCO CLOCK signal check terminal
(OUT-23 board)
VCO CLOCK signal measuring terminal.
TP501 (P-5) : CPU_OE signal check terminal
CPU_OE signal measuring terminal.
TP502 (P-5) : CPU_WE signal check terminal
CPU_WE signal measuring terminal.
TP600 (N-12), TP1000 (N-5) : 1R001 signal check
terminal (OUT-23 board)
1R001 signal measuring terminal.
TP601 (N-12), TP1001 (N-5) : HANC signal check
terminal (OUT-23 board)
HANC signal measuring terminal.
TP602 (N-11), TP1002 (N-5) : LINE signal check
terminal (OUT-23 board)
LINE signal measuring terminal.
TP603 (N-12), TP1003 (N-5) : FRAME signal check
terminal (OUT-23 board)
FRAME signal measuring terminal.
1-8. Checks on Completion of Installation