Sony DVP NC555ES User Manual
Page 75
D:\##sagyou\#05 May\824163S
DVPNC555ES_US\3082036112
DVPNC555ES_US\01US12SET-U2.fm
master page=right
DVP-NC555ES
3-082-036-11(2)
75
Set
ting
s an
d Adj
u
st
m
ent
s
◆ AUDIO FILTER (except Super Audio CD)
Selects the digital filter to reduce noise above
22.05 kHz (Sampling frequency (Fs) of the
audio source is 44.1 kHz), 24 kHz (Fs is 48
kHz), or 48 kHz (Fs is above 96 kHz).
Note
There may be little effect by changing the digital
filter depending on discs or playback environment.
◆ DOWNMIX (DVD only)
Switches the method for mixing down to 2
channels when you play a DVD which has
rear sound elements (channels) or is recorded
in Dolby Digital format. For details on the
rear signal components, see “Displaying the
audio information of the disc” (page 55). This
function affects the output of the following
jacks:
– AUDIO OUT L/R 1/2 jacks
– DIGITAL OUT (OPTICAL or COAXIAL)
jack when “DOLBY DIGITAL” and “DTS”
is set to “D-PCM” (page 75).
◆ DIGITAL OUT
Select this if audio signals are to be output via
the DIGITAL OUT (OPTICAL or
COAXIAL) jack.
Note
Super Audio CD audio signals are not output from
a digital jack.
To set the digital output signal
The following switch the method of
outputting audio signals when you connect a
component such as an amplifier (receiver) or
MD deck with a digital input jack.
For connection details, see page 21.
Select “DOLBY DIGITAL,” “DTS,” and “48
kHz/96 kHz PCM” after setting “DIGITAL
OUT” to “ON.”
If you connect a component that does not
conform to the selected audio signal, a loud
noise (or no sound) will come out from the
speakers, damaging your ears or speakers.
• DOLBY DIGITAL (DVD only)
Selects the type of Dolby Digital signal.
• DTS (DVD VIDEO only)
Selects the type of DTS signal.
SHARP
Provides a wide frequency
range and spatial feeling.
SLOW
Provides smooth and warm
sound.
DOLBY
SUR-
ROUND
Normally select this position.
Multi-channel audio signals are
output to two channels for
enjoying surround sounds.
NORMAL
Multi-channel audio signals are
downmixed to two channels for
use with your stereo.
ON
Normally select this position. When
you select “ON,” see “To set the digital
output signal” for further settings.
OFF
The influence of the digital circuit
upon the analog circuit is minimal.
D-PCM
Select this when the player is
connected to an audio
component without a built-in
Dolby Digital decoder. You can
select whether the signals
conform to Dolby Surround
(Pro Logic) or not by making
adjustments to the
“DOWNMIX” item in
“AUDIO SETUP” (page 75).
DOLBY
DIGITAL
Select this when the player is
connected to an audio
component with a built-in
Dolby Digital decoder.
D-PCM
Select this when the player is
connected to an audio
component without a built-in
DTS decoder. If you play DTS
audio sound tracks, the player
outputs stereo signals via the
DIGITAL OUT (OPTICAL or
COAXIAL) jacks.
DTS
Select this when the player is
connected to an audio
component with a built-in DTS
decoder.
AUDIO SETUP
AUDIO ATT:
AUDIO DRC:
DIGITAL OUT:
DOLBY DIGITAL:
OFF
STANDARD
AUDIO FILTER:
SHARP
ON
DOWNMIX:
DOLBY SURROUND
D-PCM
48kHz/96kHz PCM:
48kHz/16bit
DTS:
D-PCM
c
continued