Sherwood R-865 - Manual (Page 50)

50
• After you have installed this unit and connected all the components, you first perform the speaker setup settings for the
optimum sound acoustics according to your environment and speaker layout.
• Depending on your speaker type, you can select one of these following speaker types.
• Yes/No : Select the desired depending on whether a subwoofer is connected or not.
• Large : Select this when connecting speakers that can fully reproduce sounds below crossover
frequency.
• Small : Select this when connecting speakers that cannot fully reproduce sounds below crossover
frequency.When this is selected, sounds below crossover frequency are sent to the
subwoofer.
• None : Select this when no speakers are connected. When this is selected, sounds are sent to the
speakers which are not set to None.
• A/B/A+B : Select the desired depending on surround speaker connections (and whether program
source is movie or music in such a case that two sets of surround speakers are connected).
• 2CH/1CH : Select the desired depending on the number of surround back speakers.
• Each time these buttons are pressed, “ ” and “ ” are
moved to the corresponding speaker mode.
Notes :
• When speakers are set to “Small”, you should set the CROSSOVER FREQUENCY correctly according to their low frequency playback
capacity. (Refer to “When selecting the CROSSOVER FREQUENCY” on page 54.)
• When “FRONT’ is set to “Small”, “SUBWOOFER” is automatically set to “Yes”, and when “SUBWOOFER” is set to “No”, “FRONT” is
automatically set to “Large”.
• When “FRONT” is set to “Small”, “CENTER”, “SURROUND” and “SURR. BACK” cannot be set to “Large”.
• When the power amplifier for surround back channels is assigned to “ROOM2” or the surround speakers are all set to None, “S/B CH” is
automatically set to “None”.
• When “SURR. (A)” or “SURR. (B)” is set to “Small”, “SURR. BACK” cannot be set to “Large”.
• If either “SURR. (A)” or “SURR. (B)” is set to “Small”, the output is the same as when “SURR. (A)” and “SURR. (B)” are both set to “Small”.
S P E A KE R S E T U P
R E T U R N : B a c k E N T E R : S e l e c t
S P E A K E R C O N F I G U R A T I O N
S P E A K E R D I S T A N C E
V I R T U A L S P E A K E R S E T U P
S U B W O O F E R : A C T I V E
S U B W O O F E R M O D E : L F E
C R O S S O V E R F R E Q . : 8 0 H z
To select the sizes of the speakers that are connected.
To enter the distance between the listening position and each speaker to set
the delay time automatically for the optimum surround playback.
To adjust the Dolby Virtual Speaker setting modes as desired.
To select the type of the subwoofer that is connected.
To select the desired subwoofer mode
To select the desired crossover frequency
S P E A K E R C O N F I G U R A T I O N
S U B W O O F E R :
F R O N T
:
C E N T E R :
S U R R . A / B : A + B
S U R R . ( A ) :
S U R R . ( B ) :
S / B C H :
S U R R . B A C K :
R E T U R N : B a c k , : S e l e c t
Large
Large
Large
Large
Large
Yes
2CH
Press the CURSOR UP( )/DOWN( ) buttons to select the SPEAKER CONFIGURATION, then press
the ENTER button.
1
Press the CURSOR UP( )/DOWN( ) buttons to select the desired speaker.
2
Press the CURSOR LEFT( )/RIGHT( ) buttons to select the desired mode.
3
SETTING THE SPEAKER SETUP
When selecting the SPEAKER CONFIGURATION
ENGLISH