Lexmark 280 User Manual
User's guide
Advertising
Table of contents
Document Outline
- Contents
- Safety information
- Learning about the printer
- Additional printer setup
- Installing internal options
- Attaching cables
- Installing optional trays
- Verifying printer setup
- Setting up the printer software
- Setting up wireless printing
- Installing the printer on a wired network
- Changing port settings after installing a new network Internal Solutions Port
- Setting up serial printing
- Minimizing your printer's environmental impact
- Loading paper and specialty media
- Paper and specialty media guide
- Printing
- Clearing jams
- Understanding printer menus
- Understanding printer messages
- List of status and error messages
- Activating Menu Changes
- Busy
- Calibrating
- Cancel not available
- Canceling
- Change <src> to <x>
- Clearing job accounting statistics
- Close door <x>
- Copies
- Defragmenting Flash DO NOT POWER OFF
- Delete/Delete all/Delete all confidential jobs
- Deleting
- Disabling DLEs
- Disabling Menus
- Disk Corrupted. Reformat?
- Disk recovery x/y XX% DO NOT POWER OFF
- Enabling Menus
- Encrypting disk x/y XX% DO NOT POWER OFF
- Enter PIN
- Enter PIN to lock
- Flushing buffer
- Formatting Disk x/y XX% DO NOT POWER OFF
- Formatting Flash DO NOT POWER OFF
- Insert Tray <x>
- Internal System Error, Reload Bookmarks
- Internal System Error, Reload Security Certificates
- Invalid Engine Code
- Invalid Network Code
- Invalid PIN
- Load multipurpose tray with <x>
- Load <src> with <x>
- Menus are disabled
- Network/Network <x>
- No held jobs
- No jobs to cancel
- Power Saver
- Printer locked, enter PIN to unlock
- Printing
- Programming disk DO NOT POWER OFF
- Programming flash DO NOT POWER OFF
- Programming System Code DO NOT POWER OFF
- Reading USB drive DO NOT REMOVE
- Ready
- Remote Management Active DO NOT POWER OFF
- Remove all color supplies
- Remove Packaging Materials
- Remove paper from standard bin
- Resetting Fuser Count
- Resetting the printer
- Restore Held Jobs?
- Restoring Factory Defaults
- Restoring Held Job(s) x/y
- Serial <x>
- Some held jobs were not restored
- Some held jobs will not be restored
- Standard Bin Full
- Submitting Selection
- Tray <x> Empty
- Tray <x> Low
- Tray <x> Missing
- USB/USB <x>
- Waiting
- 31 Missing or defective <color> cartridge
- 32 Replace unsupported <color> cartridge
- 34 Incorrect paper type, check <src>
- 34 Incorrect paper size, check <src>
- 34 Short paper
- 35 Insufficient memory to support Resource Save feature
- 37 Insufficient memory for Flash Memory Defragment operation
- 37 Insufficient memory to collate job
- 37 Insufficient memory, some held jobs will not be restored
- 38 Memory full
- 39 Page is too complex to print
- 51 Defective flash detected
- 52 Flash full
- 53 Unformatted flash detected
- 54 Network <x> software error
- 54 Serial option <x> error
- 54 Standard network software error
- 55 Unsupported option in slot <x>
- 56 Parallel port <x> disabled
- 56 Serial port <x> disabled
- 56 Standard USB port disabled
- 56 USB port <x> disabled
- 57 Configuration change, held jobs were not restored
- 58 Too many flash options installed
- 58 Too many trays attached
- 61 Remove defective hard disk
- 62 Disk full
- 63 Unformatted disk
- 80 Fuser life warning
- 80 Replace fuser
- 82 Replace waste toner box
- 82 Waste toner box missing
- 82 Waste toner box nearly full
- 83 Replace transfer module
- 83 Transfer module life warning
- 83 Transfer module missing
- 84 <color> photoconductor low
- 84 <color> photoconductor nearly low
- 84 Replace <color> photoconductor
- 88 <color> cartridge low
- 88 <color> cartridge nearly low
- 88 Replace <color> cartridge
- 200–250.yy Paper jam
- 900–999 Service <message>
- 1565 Emul Error Load Emul Option
- List of status and error messages
- Maintaining the printer
- Administrative support
- Troubleshooting
- Checking an unresponsive printer
- Solving printing problems
- Multiple-language PDFs do not print
- Printer control panel display is blank or displays only diamonds
- Error message about reading USB drive appears
- Jobs do not print
- Confidential and other held jobs do not print
- Job takes longer than expected to print
- Job prints from the wrong tray or on the wrong paper
- Incorrect characters print
- Tray linking does not work
- Large jobs do not collate
- Unexpected page breaks occur
- Solving option problems
- Solving paper feed problems
- Solving print quality problems
- Isolating print quality problems
- Blank pages
- Characters have jagged or uneven edges
- Color misregistration
- Clipped images
- Fine horizontal lines appear on color pages
- Ghost images
- Gray background
- Incorrect margins
- Light colored line, white line, or incorrectly colored line
- Paper curls badly
- Print irregularities
- Print is too dark
- Print is too light
- Repeating defects
- Skewed print
- Solid color pages
- Streaked horizontal lines
- Streaked vertical lines
- Toner fog or background shading appears on the page
- Toner rubs off
- Toner specks
- Transparency print quality is poor
- Uneven print density
- Solving color quality problems
- Embedded Web Server does not open
- Contacting Customer Support
- Notices
- Product information
- Edition notice
- UNITED STATES GOVERNMENT RIGHTS
- Trademarks
- Federal Communications Commission (FCC) compliance information statement
- Noise emission levels
- Temperature information
- Waste from Electrical and Electronic Equipment (WEEE) directive
- Product disposal
- Battery notice
- ENERGY STAR
- Laser notice
- Power consumption
- Laser advisory label
- European Community (EC) directives conformity
- Radio interference notice
- CCC EMC notice
- BSMI notice
- Notice to Users in the European Union
- Regulatory notices for wireless products
- Exposure to radio frequency radiation
- Notice to users in Brazil
- Industry Canada (Canada)
- Taiwan NCC RF notice statement
- India emissions notice
- Notice to users in the European Union
- Statement of Limited Warranty
- LEXMARK SOFTWARE LIMITED WARRANTY AND LICENSE AGREEMENTS
- Index