Panasonic WJ-NT104 - Manual (Page 63)

63
q VIDEO IN (WJ-NT104)
Selects any of the four video inputs of the Interface Unit
for display on the monitor. Set the monitor outputs of
the Matrix Switcher to match the video inputs of the
Interface Unit, referring to MATRIX SWITCHER CON-
FIGURATION on page 62.
The video channels will be switched in accordance
with the operating mode selected. Refer to MAIN
PAGE AND CONTROLS on page 25 for a description of
operating modes and to MODE SETUP on page 41 for
mode setting procedures.
w CAMERA SELECT (Left window panel)
To select a camera (camera 01 to 08) connected to the
WJ-SX550A Matrix Switcher. The image of the selected
camera is displayed on the monitor in the previously
selected input mode.
e PRESET SELECT (Left part of screen)
To move the combination camera (option) connected to
the WJ-SX550A to any of 8 preset positions.
r ALARM LIST
Any image before and after alarm input can be tem-
porarily stored in the internal memory of the WJ-NT104.
For alarm display see ALARM LIST on page 37.
t CAMERA SELECT (Bottom window panel)
To select a camera (CAMERA 1 to 128) connected to
the WJ-SX550A. Select a camera number, and then
click
[SET] to apply it. The image of the selected cam-
era is displayed on the monitor in the previously select-
ed input mode.
y PRESET SELECT (Bottom window panel)
To move the combination camera (option) connected to
the WJ-SX550A to any of 64 preset positions. Select a
preset position number, and then click the
[SET] button
to move the camera to the position.
u TOUR SEQUENCE
To run the tour sequence of the WJ-SX550 matrix
switcher. Select a tour sequence number, and then
click the [SET] button to run the sequence.
i PROGRAM SEQUENCE
To run the program sequence of the WJ-SX550 matrix
switcher. Click the [SET] button to run the assigned
sequence.
o ALARM ALL RESET
To reset all alarms activated in the Matrix Switcher, and
return it to normal condition.
!0 ZOOM
The connected combination camera (option) can be
zoomed by clicking the
[TELE] or [WIDE] button under
ZOOM.
Clicking the
[TELE] or [WIDE] button will operate the
camera in telescopic or wide-angle mode for a speci-
fied time, after which the mode is released automatical-
ly. These modes cannot be retained by keeping the
[TELE] or [WIDE] button depressed. You need to click
the [TELE] or [WIDE] button again.
!1 FOCUS
The connected combination camera (option) can be
focused by clicking the
[FAR] , [NEAR] or [AUTO] but-
ton under FOCUS.
Clicking the
[FAR] or [NEAR] button will operate the
camera in focusing mode for a specified time, after
which the mode is released automatically. Clicking the
[AUTO] button will automatically focus the image on
the screen. Focus control cannot be retained by keep-
ing the
[FAR] or [NEAR] button depressed. You need
to click the [FAR] or [NEAR] button again.
!22 IRIS
The connected combination camera (option) can be
controlled to close or open iris by clicking the
[CLOSE]
or [OPEN] button under IRIS.
Clicking the [OPEN] or [CLOSE] button will open or
close the camera iris for a specified time, after which
the operation is released automatically.
Clicking the
[RESET] button on the screen will reset
the iris of the displayed camera to the factory default
setting. Iris control cannot be retained by keeping the
[OPEN] or [CLOSE] button depressed. You need to
click the [OPEN] or [CLOSE] button again.
!33 AUTO PAN
The auto pan status of the connected combination
camera (option) can be changed by clicking the
[ON]
or [OFF] button under AUTOPAN.
Note: When LOCAL is selected in the camera setup
menu, auto pan is released automatically after 1
minute. When REMOTE is selected, auto pan will
not be released automatically.
!4 Image Display
To display the image output from the Matrix Switcher
connected to the WJ-NT104 Interface Unit. Set the
monitor outputs of the Matrix Switcher to match the
video inputs of the Interface Unit, referring to MATRIX
SWITCHER CONFIGURATION on page 62.
!5 PAN/TILT
Clicking anywhere on the live image moves the con-
nected combination camera (option) up and down, or
to the right and left. The camera pan/tilt angle
decreases as the point clicked moves closer to the
image center. Clicking the image center will not move
the camera. Zooming does not change the camera
pan/tilt angle. Click the image repeatedly to move the
camera to the desired position. You cannot pan or tilt
the camera continuously by dragging on the live
image.