Xylem Oxix Dissolved Oxygen Transmitter - Manual (Page 70)

70 GB Oxix Manual 080915
FW: 841013-009, 846001-002, 841513-009
Dissolved Oxygen Transmitter
Communication log
View the Modbus and sensor communication logs. Primarily intended for
fault detection.
Set primary value
- - - - mg/l
Back Select >
Test primary value
Enable test
Yes
No
Back Select OK
Current
Set fixed current
Calib. current
DAC zero current
DAC top current
Back Select OK
Calib. current
- - - - uA
Back Select OK
Calibrate mA
Current
- - - - uA
Back Select OK
Set fixed current
Release mA
Minimum mA
4 mA
12 mA
20 mA
Maximum mA
Back Select OK
DAC zero current
- - - - uA
Back Select OK
DAC top current
- - - -
Back Select OK
No Hour Event Extension
1 154 0 0
2 154 0 0
3 154 0 0
4 154 0 0
Back Select >
Read eventlog
No Hour Event Extension
5 154 0 0
6 154 0 0
7 154 0 0
8 154 0 0
Back Select >
No Hour Event Extension
13 154 0 0
14 154 0 0
15 154 0 0
16 154 0 0
Back Select >
No Hour Event Extension
9 154 0 0
10 154 0 0
11 154 0 0
12 154 0 0
Back Select >
No Hour Event Extension
17 154 0 0
18 154 0 0
19 154 0 0
20 154 0 0
Back Select >
Recover Factory Settings
Cancel
Back on Stock
Sensor Factory Reset
Back Select OK
Back on stock
Sensor Factory Reset
No
Yes
Back Select Ok
Modbus
Rx ok 4950
Rx CRC error 4564
Rx paritet error 4545
Rx adr. error 4566
Rx wrong id 4950
Tx count 3454
Back Select OK
Communication log
Sensor
Rx ok 4950
Rx CRC error 4564
Rx paritet error 4545
Rx count 4950
Tx count 3454
Back Select OK
Autodetect sensor type
Use
Not in use
Back Select OK
Mains supply frequency
50 Hz
60 Hz
Back Select OK
Autodetect sensor type Mains supply frequency
GB Oxix menuer #1 Service menu 2 FW: 841013-009, 846001-002, 841513-009 Page 6 of 7 15. september 2008
Back on stock
The factory settings can be re-etablished with the "Back on stock" option.
Set primary value
- - - - mg/l
Back Select >
Test primary value
Enable test
Yes
No
Back Select OK
Current
Set fixed current
Calib. current
DAC zero current
DAC top current
Back Select OK
Calib. current
- - - - uA
Back Select OK
Calibrate mA
Current
- - - - uA
Back Select OK
Set fixed current
Release mA
Minimum mA
4 mA
12 mA
20 mA
Maximum mA
Back Select OK
DAC zero current
- - - - uA
Back Select OK
DAC top current
- - - -
Back Select OK
No Hour Event Extension
1 154 0 0
2 154 0 0
3 154 0 0
4 154 0 0
Back Select >
Read eventlog
No Hour Event Extension
5 154 0 0
6 154 0 0
7 154 0 0
8 154 0 0
Back Select >
No Hour Event Extension
13 154 0 0
14 154 0 0
15 154 0 0
16 154 0 0
Back Select >
No Hour Event Extension
9 154 0 0
10 154 0 0
11 154 0 0
12 154 0 0
Back Select >
No Hour Event Extension
17 154 0 0
18 154 0 0
19 154 0 0
20 154 0 0
Back Select >
Recover Factory Settings
Cancel
Back on Stock
Sensor Factory Reset
Back Select OK
Back on stock
Sensor Factory Reset
No
Yes
Back Select Ok
Modbus
Rx ok 4950
Rx CRC error 4564
Rx paritet error 4545
Rx adr. error 4566
Rx wrong id 4950
Tx count 3454
Back Select OK
Communication log
Sensor
Rx ok 4950
Rx CRC error 4564
Rx paritet error 4545
Rx count 4950
Tx count 3454
Back Select OK
Autodetect sensor type
Use
Not in use
Back Select OK
Mains supply frequency
50 Hz
60 Hz
Back Select OK
Autodetect sensor type Mains supply frequency
GB Oxix menuer #1 Service menu 2 FW: 841013-009, 846001-002, 841513-009 Page 6 of 7 15. september 2008