DoorKing 1833 PC Programmable - Manual (Page 32)

1835-065-E-7-13 30
3.3 General Programming Using the System Keypad
System Keypad
Proceed with the programming steps on the following pages ONLY IF PC programming WILL NOT be
used. The system keypad may be used to program some features on the telephone entry system but can
be a little tedious to use. We strongly suggest that you become familiar with the programming steps in
each feature you want to use BEFORE actually programming the system.
These steps will program Relay 0 (relay 0 is not available for the 1834), Relay 1 and Relay 2 strike times. Strike times can be
programmed from 1/4 second up to 99 seconds by entering the desired time in seconds as a two-digit number in step 3. If
Expansion boards are going to be used with this system, set Relay 2 strike time to 00 for Expansion boards 1-8. If more than 8
Expansion boards are being used, set Relay 1 strike time to 00 (for Expansion boards 9-16) and then set Relay 0 strike time for
the desired time in seconds. In this application, Relay 0 becomes the PRIMARY relay that will open the door or gate after the
resident presses 9 on their telephone.
Factory setting for relay strike times are: Relay 0 = 01 (1 sec), Relay 1 = 01 (1 sec), Relay 2 = 01 (1 sec).
3.3.1 Relay Strike Time
This programming sequence sets the maximum time allowed for conversation when the entry system places a call to the
resident. The talk time can be set from 1 second up to 255 seconds (4 minutes, 15 seconds) and is entered as a three-digit
number in step 3. The talk time set here DOES NOT affect the telephone numbers that are programmed under directory codes 0,
00, 000, 0000 and 1, 01, 001, 0001. The talk time for these two directory code sets are factory set to the maximum. Phone
numbers programmed under these directory codes should be reserved for management or emergency phone numbers that
generally require longer conversations.
Factory setting for talk time = 060 (60 seconds).
3.3.2 Talk Time
77 88 99
44 55 66
11 22 33
00 OPER OPER
WXYZ WXYZ TUV TUV PQRS PQRS
MNO MNO JKL JKL GHI GHI
DEF DEF ABC ABC SP SP
CALL
Z
A
1. Press and enter your four-digit MASTER CODE (beep).
2. Press (beep) to set Relay 0, OR (beep) to set Relay 1, OR (beep) to set Relay 2 strike time.
Note: “0 * ” - Relay 0 is not available for the 1834.
3. Enter the two-digit strike time in seconds (00-99), then press (beep).
(Example: 1/4 second - enter 00, 1 second - enter 01 etc.)
4. Repeat steps 2 and 3 to set other relay strike times.
5. Press together to end this programming sequence (beeeeeep).
?? ?? ?? ??
33
DEF DEF
00
OPER OPER
00
OPER OPER
11
SP SP
22
ABC ABC
00
OPER OPER
1. Press and enter your four-digit MASTER CODE (beep).
2. Press (beep) to set Relay 0, OR (beep) to set Relay 1, OR (beep) to set Relay 2 strike time.
Note: “0 * ” - Relay 0 is not available for the 1834.
3. Enter the three-digit talk time in seconds (001-255), then press (beep).
(Example: 1 second - enter 001, 20 seconds - enter 020 etc.)
4. Press together to end this programming sequence (beeeeeep).
?? ?? ?? ??
88
TUV TUV
00
OPER OPER
00
OPER OPER
11
SP SP
22
ABC ABC
00
OPER OPER
Important Note: If you make a mistake while programming, press keys at the same time
to escape from programming no matter how much has been completed, then begin again at step 1.
00
OPER OPER