FEC AFC1100 - Manual (Page 6)

)(& ,QF
4.4.2 Offset Tool
FIG. 4-4-2 Offset Tool
32 52 6.5 15 30 6 255 502 50 757 807 110 50 502M4-O
25 42 5.5 13 25 5 202.5 385 40 587.5 627 150 30 302M3-O
20 38 5.5 10 20 5 202.5 345 40 547.5 587.5 220 20 202M3-O
20 38 5.5 10 20 5 202.5 303 40 505.5 545.5 315 15 152M3-O
20 34 5.5 10 20 5 202.5 309 40 511.5 551.5 400 13 132M3-O
16 30 4.5 8 16 5 202.5 269 40 471.5 511.5 500 8 801M3-O
601M3-O
16 30 4.5 8 16 5 147 269 40 416 456 500 4 401M2-O
12 22 3.5 5 12 5 140 258 30 398 428 250 4 401M1-O
12 22 3.5 5 12 5 140 236 30 376 406 500 2 201M1-O
12 22 3.5 5 12 5 140 236 30 376 406 500 1 101M1-O1
K J I H G F E D C B A SPEED
(rpm)
TORQUE
(kgm)
DFT-
TYPE
24 260 98.3 18 138.4 30 M10 60 72 35 122 80 73 25.4 502M4-O
14 217 82.7 12 121 27 M10 50 55 30 100 76 73 19 302M3-O
9 194 68 10 99 22 M8 45 55 20 85 62 54 15.8 202M3-O
8.8 194 68 10 99 22 M8 45 55 20 85 62 54 15.8 152M3-O
8 179 62.6 10 92.6 19 M6 45 55 18 80 60 54 15.8 132M3-O
8 142 57 8 86.7 17 M6 40 42 18 70 54 51 12.7 801M3-O
601M3-O
5.5 142 57 8 86.7 17 M6 40 42 18 70 54 51 12.7 401M2-O
3 128 35.8 7 55.8 12 M4 30 24 16 45 40 38 9.5 401M1-O
3 128 35.8 6 56 12 M4 30 24 16 45 40 38 9.5 201M1-O
3 128 35.8 6 56 12 M4 30 24 16 45 40 38 9.5 101M1-O1
WEIGHT
(Kg)
W V U T S TAP R Q P O N M L DFT-
TYPE
4.4.3 Mounting Plate Design Requirements
The plate to which the tools are mounted must maintain the following specifications:
P Plate must be blanchard ground (to ensure sides are adequately flat and parallel)
to a thickness of 15.88 mm (.625 inch) +/- 0.05 mm (.002 inch).
P Chamfer all bores on both sides by 1.6 mm (.063 inch) x 45 degrees.
P Tools must be mounted 1.6 mm (.063 inch) apart, at a minimum.
Chapter 4: System Setup and Wiring (Rev. 8/98)
Page 4-6