Document Outline

• Inhaltsverzeichnis
  • 1 Mounting 5
  • 2 Electrical connections 6
    • 2.1 Connecting diagram 6
    • 2.2 Terminal connection 6
  • 3 Operation 10
    • 3.1 Front view 10
    • 3.2 Behaviour after power-on 10
    • 3.3 Operating level 11
      • 3.3.1 Min/max function 11
      • 3.3.2 Tare function 12
      • 3.3.3 Sample&hold amplifier 12
      • 3.3.4 O2 measurement 13
      • 3.3.5 Extended operating level 14
      • 3.3.6 Alarm handling 15
    • 3.4 Maintenance manager / Error list 16
  • 4 Controller 17
    • 4.1 Operation 17
    • 4.2 Control parameters 17
    • 4.3 Self-tuning 18
      • 4.3.1 Self-tuning start ( Щ + И ) 18
      • 4.3.2 Self-tuning cancellation 18
      • 4.3.3 Acknowledgement procedures in case of unsuccessful self-tuning 19
      • 4.3.4 Examples for self-tuning attempts 19
      • 4.3.5 (controller inverse, heating or heating/cooling) 19
    • 4.4 Manual tuning 20
    • 4.5 Operating structure 22
  • 5 Configuration level 23
    • 5.1 Configuration survey 23
    • 5.2 Configuration 24
    • 5.3 Configuration examples 30
      • 5.3.1 On-Off controller / Signaller (inverse) 30
      • 5.3.2 2-point controller (inverse) 31
      • 5.3.3 Continuous controller (inverse) 32
      • 5.3.4 Digital 280-1 with measured value output 33
  • 6 Parameter setting level 34
    • 6.1 Parameter survey 34
    • 6.2 Parameter 35
    • 6.3 Input scaling 36
      • 6.3.1 Input Inp 36
  • 7 Calibration level 37
    • 7.1 Offset correction 37
  • 8 BlueControl 40
  • 9 Versions 41
  • 10 Technical data 42
  • 11 Safety hints 46
    • 11.1 Resetting to factory setting 47
• Index
  • 0-9
    • 2-point correction 37
  • A
    • Alarm handling 15
    • Anschlußbeispiele
      • OUT3 als Logikausgang 8
  • B
    • BlueControl 40
    • Bus interface
      • Technical Data 43
  • C
    • Calibration (CAL) 37
    • Calibration level (CAL) 37 - 39
    • Configuration examples
      • 2-point controller 31
      • Signaller 30
    • Configuration level
      • Parameter survey 23
    • Configuration-level (ConF)
      • Configuration-Parameter 24 - 29
    • Connecting diagram 6
    • Connecting examples
      • di2/3, 2-wire transmitter supply 7
      • OUT3 transmitter supply 7
      • RS485 interface 8
    • continuous controller 32
    • control inputs di1, di2, di3
      • Configuration 27
  • D
    • Digital inputs di1, di2, di3
      • Technical data 42
  • E
    • Equipment 41
  • F
    • Factory setting 22
    • Front view 10
    • Frontansicht 10
  • I
    • Input INP1
      • configuration 24
      • Parameter setting 35
    • Input scaling 36
  • L
    • LED
      • Ada - LED 10
      • Err - LED 10
      • ì - LED 10
      • SP.x - LED 10
  • M
    • Maintenance manager 16
    • measured value output 33
    • Mounting 5
  • O
    • Offset correction 37 - 39
    • operating structure 22
    • Output OUT1
      • Configuration 26
      • Technical data 42
    • Output OUT2
      • Configuration 26
      • Technical data 42
    • Output OUT3
      • Configuration 26
  • P
    • Parameter setting level
      • Parameter survey 34
    • Parameter-Level (PArA)
      • Parameter 35
  • R
    • Resetting to factory setting 47
  • S
    • Safety hints 46 - 47
    • Safety switch 5
    • Safety test 44
    • Selbstoptimierung
      • Start 18
    • Self-tuning
      • Cancelation 18
      • Start 18
  • V
    • Versions 41