The edges of the paper are dirty – Canon imagePROGRAF iPF760 User Manual
Page 94
Cause
Corrective Action
Paper has been loaded incorrectly, caus-
ing it to wrinkle.
Reload the paper.
(See "Loading Rolls in the Printer.")
(See "Loading Sheets in the Printer.")
The Printhead is set too low in the Control
Panel menu.
In the Control Panel menu, set Head Height to Automatic.
(See "Adjusting the Printhead Height.")
→User's Guide
You are printing on heavyweight paper or
paper that curls or wrinkles easily after
absorbing ink.
When printing on Heavyweight Coated Paper or other paper-based media, choose a Vac-
uumStrngth setting of Strong or Strongest in the Control Panel menu. If the paper still rubs,
set Head Height to Highest in the Control Panel menu.
(See "Adjusting the Vacuum Strength.")
→User's Guide
(See "Adjusting the Printhead Height.")
→User's Guide
When printing on CAD Tracing Paper or other film-based media, choose a VacuumStrngth
setting of Standard, Strong, or Strongest in the Control Panel menu. If the paper still rubs,
set Head Height to Highest in the Control Panel menu.
(See "Adjusting the Vacuum Strength.")
→User's Guide
(See "Adjusting the Printhead Height.")
→User's Guide
When printing on paper 0.1 mm (0.004 in) thick or less, choose a VacuumStrngth setting of
Weakest in the Control Panel menu. If the paper still rubs, set Head Height to Highest in the
Control Panel menu.
(See "Adjusting the Vacuum Strength.")
→User's Guide
(See "Adjusting the Printhead Height.")
→User's Guide
When you have loaded paper, the paper
you have loaded does not match the type
selected on the Control Panel.
Be sure to select the correct type of paper in the Control Panel menu when loading paper.
(See "Loading Rolls in the Printer.")
(See "Loading Sheets in the Printer.")
The edges of the paper are dirty
The edges of the paper are dirty
Cause
Corrective Action
The Platen has become dirty after border-
less printing or printing on small paper.
Open the Top Cover and clean the Platen.
(See "Cleaning Inside the Top Cover.")
The type of paper as specified on the print-
er does not match the type specified in the
printer driver.
Make sure the same type of paper is specified on the printer as in the printer driver.
(See "Changing the Type of Paper.")
→User's Guide
Make sure the same paper type is specified in the printer driver as on the printer.
1.
Press the Stop button and stop printing.
2.
Change the type of paper in the printer driver and try printing again.
The paper is wrinkled or warped.
Straighten out the wrinkles or curls and reload the paper. Do not use paper that has been
printed on previously.
(See "Loading Rolls in the Printer.")
(See "Loading Sheets in the Printer.")
A cut line is printed because CutDustRe-
duct. is On in the Control Panel menu to re-
duce cutting dust.
If this function is not needed, set CutDustReduct. to Off in the Control Panel menu.
(See "Menu Settings.")
→User's Guide
The Printhead is set too low in the Control
Panel menu.
In the Control Panel menu, set Head Height to Automatic.
(See "Adjusting the Printhead Height.")
→User's Guide
You are printing on heavyweight paper or
paper that curls or wrinkles easily after ab-
sorbing ink.
When printing on Heavyweight Coated Paper or other paper-based media, choose a Vac-
uumStrngth setting of Strong or Strongest in the Control Panel menu. If the paper still
rubs, set Head Height to Highest in the Control Panel menu.
(See "Adjusting the Vacuum Strength.")
→User's Guide
(See "Adjusting the Printhead Height.")
→User's Guide
When printing on CAD Tracing Paper or other film-based media, choose a VacuumStrngth
setting of Standard, Strong, or Strongest in the Control Panel menu. If the paper still rubs,
set Head Height to Highest in the Control Panel menu.
(See "Adjusting the Vacuum Strength.")
→User's Guide
(See "Adjusting the Printhead Height.")
→User's Guide
The Ejection Guide is soiled.
Clean the Ejection Guide.
The edges of the paper are dirty
iPF760
Troubleshooting
Problems with the printing quality
94