Pioneer DJM-800 - Manual (Page 18)

18
<DRB1392>
En
EFFECT PARAMETERS
Beat Effect
EFFECT FUNCTIONS (EFFECT PARAMETERS)
Sound-color effects
Name
1 HARMONIC
2 SWEEP
3 CRUSH
4 FILTER
Parameter (COLOR dial)
Sets amount of pitch shift in range of ±6 half-tones. Rotating dial
to right increases pitch shift by +6 half-tones, while rotating to the
left reduces pitch shift by –6 half-tones.
Sets filter's cutoff frequency. Rotating dial clockwise produces
band-pass filter effect; rotating counterclockwise produces notch
filter effect.
Sets amount of crushing of input sound. Rotate dial
counterclockwise to emphasize low-range sounds, and rotate
clockwise to emphasize high-range sounds.
Sets cutoff frequency of filter. Rotating dial to right changes high-
pass filter; rotating dial to left changes low-pass filter.
Name
1 DELAY
2 ECHO (*1)
3 REVERSE DELAY
4 PAN
5 TRANS
6 FILTER
7 FLANGER
8 PHASER
9 REVERB (*1)
10 ROBOT
11 CHORUS
12 ROLL (*2)
13 REVERSE ROLL (*2)
14 SEND/RETURN
Beat Switch Parameter
Sets delay time of 1/8 to 16/1 per 1
beat of BPM time.
Sets delay time of 1/8 to 16/1 per 1
beat of BPM time.
Sets delay time of 1/8 to 16/1 per 1
beat of BPM time.
Sets time of 1/16 to 16/1 per 1 beat of
BPM time for distribution to right/left.
Sets cut time of 1/16 to 16/1 per 1
beat of BPM time.
Cycle of cutoff frequency shift is set
in unit of 1/4 to 64/1 relative to 1
beat of BPM.
Cycle of flanger shift is set in units
of 1/4 to 64/1 relative to 1 beat of
BPM.
Cycle of phaser effect shift is set in
units of 1/4 to 64/1 relative to 1 beat
of BPM.
Amount of reverberation is set from
1 to 100 %.
Sets pitch of robot sound effect
within range of –100 to +100 %.
Cycle of chorus sound waver is set
in units of 1/4 to 64/1 relative to 1
beat of BPM.
Effect time is set as 1/16 to 16/1
relative of 1 beat of BPM.
Effect time is set as 1/16 to 16/1
relative of 1 beat of BPM.
—
Contents
Sets delay time.
Sets delay time.
Sets delay time.
Sets effect time.
Sets effect time.
Sets cycle for
cutoff time shift.
Sets cycle for
flanger effect
shift.
Sets cycle for
phase effect shift.
Sets amount of
reverberation
effect.
Sets pitch of
robot sound
effect.
Sets cycle of
chorus sound
harmonic.
Sets effect time.
Sets effect time.
—
Setting Range (unit)
1 to 4 000 (ms)
1 to 4 000 (ms)
10 to 4 000 (ms)
10 to 16 000 (ms)
10 to 16 000 (ms)
10 to 32 000 (ms)
10 to 32 000 (ms)
10 to 32 000 (ms)
1 to 100 (%)
–100 to +100 (%)
10 to 32 000 (ms)
1 to 4 000 (ms)
1 to 4 000 (ms)
—
Parameter 2
(MIX/DEPTH dial) contents
Sets balance between original and
delay sound.
Sets balance between original
sound and echo sound.
Sets balance between original and
delay sound.
Sets balance between original
sound and effect sound.
Sets balance between original
sound and effect sound.
Amount of effect increases when
dial is turned clockwise.
Amount of effect increases when
dial is turned clockwise. When dial
is turned fully counterclockwise,
only original sound is output.
Amount of effect increases when
dial is turned clockwise. When dial
is turned fully counterclockwise,
only original sound is output.
Sets balance between original
sound and effect sound.
Amount of effect increases when
dial is turned clockwise.
Sets balance of chorus sound.
Sets balance of original sound and
roll sound.
Sets balance of original sound and
roll sound.
Sets volume of RETURN input
sound.
Parameter 1 (TIME dial)
(*1) Even if the effect monitor is turned ON, if no sound is output from the channel to the master output, the effect sound will not be heard.
(*2) When effect is disabled (OFF), the effect sound will not be heard, even if monitor is set to effector.