JLG TF6-42 (9150-4003) Operator Manual - Manual (Page 15)

Form No. 20136 3/03 • TF6-42 Owner/Operator Manual
2.3
Located on right cab wall
P/N 9150-3088
Located inside engine cover
P/N 9150-3113
Located on left side, front cab plate
P/N 9116-4094
000850
THE PROTECTION OFFERED BY THIS
ROPS WILL BE IMPAIRED IF IT HAS BEEN
SUBJECTED TO ANY MODIFICATION,
STRUCTURAL DAMAGE, OR HAS BEEN
INVOLVED IN AN OVERTURN INCIDENT.
THIS ROPS MUST BE REPLACED AFTER
A ROLL-OVER. SEAT BELTS MUST BE
WORN WHILE OPERATING VEHICLE.
GRADALL MATER 06 / 9 / 10
MAX WEIGHT : 2150
MEETS SAE : J1040 MA
MEETS ISO : 3471 (94) / 3
MEETS ANSI : B56.6 - 8.16 / P
GRADALL : 9114-3261 SERIAL : 8
Box 61 SD 57201
SAMPLE ONLY
Located on back wall, behind
operator’s seat
P/N N/A (enclosed cab)
P/N N/A (open cab)
Located on right cab wall
P/N 9150-3102
21,500
21,310
24" 24"
24" 24"
42' 24"
AS RELEASED FROM FACTORY THIS TRUCK MEETS THE DESIGN SPECIFICATIONS
ESTABLISHED IN AMERICAN NATIONAL STANDARDS FOR POWERED INDUSTRIAL
TRUCKS PART III ASME B56.6b-1998.
CAP#
X1000
A
B
C
D
ATTACHMENT TRUCK & ATTACHMENT
WEIGHT
24"
D C B A
6.6 21,030
CAP#
1000
9150-3088 (A)
42'
6.6 1.2
42' 24" 24"
6.6 21,140
6.6 42' 24" 24"
24" 24" 42' 6.6
CAPACITY WITH STANDARD 48" & 72" CARRIAGE.
SHIPPED WITH
2.0'
4.6'
26.9'
B
C
A
D
2.0'
2.0'
2.7'
2.7'
FORKS RATED LESS THAN THE ATTACHMENT CAPACITY SHOWN ABOVE DECREASE CAPACITY OF ATTACHMENT TO THAT OF FORKS. FORKS RATED MORE THAN
ATTACHMENT CAPACITY DO NOT INCREASE ATTACHMENT CAPACITY.
*WEIGHTS ARE BASED ON USING 2 X 4 X 48" FORKS (APPROX. 268# PER PAIR)
**BUCKET DIMENSIONS (A & D) REFER TO BUCKET LIP HEIGHT. ***TRUSS BOOM DIMENSIONS (A & D) REFER TO HOOK CENTER.
****WEIGHT IS BASED ON SP'L SWING MAST FORKS (APPROX. 230# PER PAIR) *****PLATFORM DIMENSIONS (A & D) REFER TO CENTER OF FLOOR.
4.5 20,780 42' --- --- 4.3'
4.5 20,960 42' --- --- 4.9'
4.5 21,000 42' --- --- 4.3'
2.0 20,830 52' --- --- 3.8'
2.0 21,010 52' --- --- 3.8'
2.0 20,950 57' --- --- 4.3'
2.0 21,140 57' --- --- 4.3'
6.0 22,000 39' 24" 24" 1.9'
6.0 22,100 39' 24" 24" 1.9'
4.0 22,880 48' 24" 24" 4.2'
6.0 21,800 31' 24" 24" 4.4'
1.8 21,040 42' --- --- 4.7'
TF6-42
GRADALL IS A REGISTERED TRADEMARK FOR HYDRAULIC EQUIPMENT BUILT BY THE JLG COMPANY 1 JLG DRIVE, McCONNELLSBURG, PA. U.S.A.
20280 LBS
48" CARRIAGE
P/N 9140-5073 *
72" CARRIAGE
P/N 9140-5074 *
48" SLOPE PILER
P/N 9140-5101 *
72" SLOPE PILER
P/N 9140-5079 *
(WITHOUT ATTACHMENTS)
60" 3/4 YD BUCKET
P/N 9140-5054 **
74" 1 1/4 YD BUCKET
P/N 9140-5055 **
102" 1 1/4 YD BUCKET
P/N 9140-5071 **
10FT TRUSS BOOM
P/N 9140-5083 ***
15FT TRUSS BOOM
P/N 9140-5082 ***
6FT MAST W/72" CARR.
P/N 9140-5061 *
6FT SWING MAST
P/N 9140-5070 ****
72" 100° SWING CARR.
P/N 9140-5075 *
WORK PLATFORM
P/N 9141-5025 *****
6FT MAST W/48" CARR.
P/N 9140-5060 *
10FT TRUSS BOOM W/WINCH
P/N 9140-5081 ***
15FT TRUSS BOOM W/WINCH P/N 9140-5080 ***
R
SAMPLE ONLY - USE CHART IN CAB
13.00-33.5 12 PLY LSW G-2 Check 65 PSI (448 kPa)
Diesel Engine
SERVICE INTERVALS
LUBRICATION AND MAINTENANCE
MATERIAL HANDLER
9150-3113 REV -
Use this chart in conjunction with the "Lubrication & Maintenance" and "Recommended
Lubricants & Capacities" sections of the Owner/Operator Manual.
Service intervals may need to be more frequent than those shown depending upon
application severity. Consult your Gradall dealer for recommendations.
It is recommended that engine oil and filter, transmission lubricant and filter,
transfer case lubricant and axle lubricant be changed after first 100 hours on
new, or rebuilt units.
LUBRICANT TYPE
OR
SPECIFICATION
Air Cleaner Element
Fuel Filter
Engine Oil Filter
Engine Oil
Coolant
Diesel Fuel
YEARLY
OR
1500 HRS
6 MO.
OR
1000 HRS
3 MO.
OR
500 HRS
EVERY 5
WKS OR
250 HRS
WEEKLY
OR
50 HRS
DAILY
OR
10 HRS
Transmission
Lubricant
Filter
Transfer Case
Lubricant
Center Section
Axle Lubricant
Planetary Hubs
Filter
Lubricant
Hydraulic System
Breather/Filter
Grease Fittings
Axles (6 Pts. Ea.)
Boom Head Pivot (2 Pts.)
Boom Pivot (2 Pts.)
Extend Chain Sheave (1 Pt.)
Drive Shafts (1 Pt. Ea.)
Cylinder Pins(13 Pts.)
Quick Switch Pin (1 Pt.)
Retract Chain Sheave (1 Pt.)
Boom
Front Bottom Bearing Pads
All Other Bearing Pads
Extend/Retract Chains
Options And Attachments
Stabilizer Cylinder (3 Pts.)
Attachment Pivots And Pins
Tires
Lug Nut Torque Torque
Check
Check
Check
Check
Check
Check
Check
Check
Check
Check
Check
Grease
Grease
Grease
Grease
Grease
Grease
Grease
Grease
Grease
Grease
Grease
Grease
Change
Change
Change
Change
Change
Change
Change
Change
Change
Change
Change
Change
SAE 15W-40 CE Oil
Etheylene Glycol
No. 2 Diesel Fuel
Mobil 424
Mobil 424
Mobil 424
Mobil 424
Mobil 424
Mystik Tetrimoly
Mystik Tetrimoly
Mystik Tetrimoly
Mystik Tetrimoly
Mystik Tetrimoly
Mystik Tetrimoly
Mystik Tetrimoly
Mystik Tetrimoly
Mystik Tetrimoly
Mystik Tetrimoly
Mystik Tetrimoly
Mystik Tetrimoly
See Manual
350-400 Lb-Ft (39-45 Nm)
Fill
Work Platform Pins Grease Mystik Tetrimoly
SAMPLE ONLY - USE CHART IN CAB
9150-3102 REV. -
DECALS