Introduction, General, Operator qualifications – JLG TF6-42 (9150-4003) Operator Manual User Manual

Page 7: Orientation, Related manuals & decals, Models covered, Serial number location, Important notice, Sample only, Truck & attachment weight

Advertising

Form No. 20136 3/03 • TF6-42 Owner/Operator Manual

General

This Manual provides important information regarding safe operating and
maintenance requirements for JLG/GRADALL Material Handlers. Refer to front
cover for specific model and serial number range.

If you have any questions regarding the material handler, contact your JLG/
GRADALL Distributor.

Operator Qualifications

Operators of the material handler must be in good physical and mental
condition, have normal reflexes and reaction time, good vision and depth
perception and normal hearing. He must not be using medication which could
impair abilities nor be under the influence of alcohol or any other intoxicant
during the work shift.

The operator should possess a valid, applicable driver’s license and must
have completed a training course for this type of equipment.

In addition, the operator must read/view, understand and comply with
instructions contained in the following material furnished with the material
handler:
• This Owner/Operator Manual
• The Transformer Series Work Platform Owner/Operator Manual
• ANSI Responsibilities Manual
• EMI Aerial Work Platform Safety Manual
• GRADALL Material Handler Safety Manual
• All instructional decals and plates
• Any optional equipment instructions furnished

The operator must also read, understand and comply with all applicable
Employer, Industry and Governmental rules, standards and regulations.

Orientation

When used to describe the location of components in the material handler,
the directions “front’”, “rear”, “right” and “left” relate to the orientation of a
person sitting in the operator’s seat. (See figure I-1)

Related Manuals & Decals

Separate publications are furnished with the material handler to provide
information concerning safety, replacement parts, maintenance procedures,
theory of operation and vendor components. Replacement manuals, decals
and instruction plates can be ordered from your JLG/GRADALL Distributor.

Models Covered

This Manual covers basic information for JLG/Gradall Material Handlers. Detailed
information for each particular machine is in the maintenance section in the
back of this manual. Be certain to refer to proper information for your unit
and the optional equipment furnished on your machine.

Serial Number Location

(See figure I-2)

Specify Model Number and Serial Number when ordering parts and when
discussing specific applications and procedures with your Distributor. The
model/serial number plate is located inside the operator’s cab, right wall.

NOTE!

“Material handler” and handler

are used interchangeably
throughout this Manual.

Though no offense or

discrimination is intended, only
the masculine pronouns will be

used throughout the remainder

of this Manual.

NOTE!

REAR

FRONT

RIGHT

LEFT

Figure I-1

Figure I-2

INTRODUCTION

24"

406 MILL AVE. S.W., NEW PHILADELPHIA, OHIO 44663

GRADALL IS A REGISTERED TRADEMARK FOR

HYDRAULIC EQUIPMENT BUILT BY THE

GRADALL CO. MANUFACTURED IN THE U.S.A.

AS RELEASED FROM FACTORY THIS TRUCK MEETS THE DESIGN SPECIFICATIONS

ESTABLISHED IN AMERICAN NATIONAL STANDARDS FOR POWERED INDUSTRIAL

TRUCKS PART III ASME B56.6b-1998.

CAP#

X1000

A
B

42'

6.6

1.0

CAPACITY WITH STANDARD

48" & 72" CARRIAGE.

(WITHOUT

ATTACHMENTS)

4.6'

20,650

20,460

24"

42'

24"

C
D

ATTACHMENT

TRUCK &

ATTACHMENT

WEIGHT

24"

6.6

20,180

CAP#

1000

9147-3131 (B)

42'

24"

6.6

20,290

6.6

42'

24"

42'

6.6

48" CARRIAGE

P/N 9140-5073 *
72" CARRIAGE

P/N 9140-5074 *

SHIPPED

WIT

48" SLOPE PILER

P/N 9140-5101 *
72" SLOPE PILER

P/N 9140-5079 *

2.0'

26.9'

2.0'

2.7'

FORKS RATED LESS THAN THE ATTACHMENT CAPACITY SHOWN ABOVE DECREASE

CAPACITY OF ATTACHMENT TO THAT OF FORKS. FORKS RATED MORE THAN

ATTACHMENT CAPACITY DO NOT INCREASE ATTACHMENT CAPACITY.

*WEIGHTS ARE BASED ON USING 2 X 4 X 48" FORKS (APPROX. 268# PER PAIR)

**BUCKET DIMENSIONS (A & D) REFER TO BUCKET LIP HEIGHT.

***TRUSS BOOM & WINCH DIMENSIONS (A & D) REFER TO HOOK CENTER.

****WEIGHT IS BASED ON SP'L SWING MAST FORKS (APPROX. 230# PER PAIR)

*****PLATFORM DIMENSIONS (A & D) REFER TO CENTER OF FLOOR.

19430 LBS

SAMPLE ONLY

In the U.S.A., the operator
must have completed a training

course meeting the OSHA

Powered Industrial Truck
Operator Training

Requirements (CFR 1910.178)

NOTE!

12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234

Important Notice !

This machine has been equipped with a serial number specific Transformer Series

Personnel Work Platform. Do not exchange transformer platforms between

machines. Doing so will require calibration changes to the controller that must be

performed by a qualified service technician. This platform assembly is designed

soley for use with the Transformer Model Machines only.

Advertising

Popular Brands

Popular manuals