General Machine Products 89000 Cable Blowing Machine(Previous) - Manual (Page 55)

Page 55 of 64 General Machine Products Co., Inc.
How to specify the collets and seals to match your cable and duct size .
1. Select one (1) Duct Clamp (locator A) that represents the inside diameter of the duct that you're using.
2. Select one (1) Duct Seal (locator B) that represents the inside diameter of the duct that you're using.
3. Select the Cable Collet (locator C). Always use a Cable Collet on the cable exit side.
If you use either 6-9 mm or 9-12 mm cable, use a Cable Guide (locator D) on the cable in feed side,
for anything larger than these sizes, use a Cable Collet on the in feed side.
4. Select the Cable Seals (locator E) that match your cable size.
5. Select one (1) Cable Seal Plug (locator F) that match your cable size.
A
B
C
E
Exit Side In Feed Side
Let our "Cable Blowing Experts" tailor your configuration. Please don't hesitate to call our Hotline at 1-800-345-6009 for
any questions you may have.
Locator Description
Qty needed
(A) Duct Clamp 1 (2 halves)
(B) Duct Seal 1 (2 halves)
(C) Cable Collet 1 or 2 (2 halves) see note 3
(D) Cable Guide 0 or 1 (2 halves) see note 3
(E) Cable Seals 1 (pkg of 10)
(F) Cable Seal Plug 1 unit
In order to configure your Tornado to work
with your specific cable requirements you
must select items below that match your
duct and cable size at additional charge
89021 DUCT CLAMP 1"
89041 DUCT CLAMP 1.25"
89061 DUCT CLAMP 1.50"
89071 DUCT CLAMP 2"
(Loc A) DUCT CLAMPS (1.00-2.00") (I.D.)
(Loc C & D) CABLE COLLETS (6-28 MM) & GUIDES (6-12 MM)
89081 6-9 MM (.23 - .35") (1 Collet REQ) (exit side) Collet & guide used together
for this size cable
89082 6-9 MM (.23 - .35") (1 Guide REQ) (in feed side)
89083 9-12 MM (.35 - .47") (1 Collet REQ) (exit side) Collet & guide used together
for this size cable
89084 9-12 MM (.35 - .47") (1 Guide REQ) (in feed side)
89091 12-16 MM (.47 - .63") (2 Collets REQ)
89092 16-20 MM (.63 - .79") (2 Collets REQ)
89101 20-24 MM (.79 - .95") (2 Collets REQ)
89102 24-28 MM (.95 - 1.10") (2 Collets REQ)
Same collet used on both in
feed
and exit side
89125 6-7.5 MM (.23 - .29")
89126 7.5-9 MM (.29 - .35")
89127 9-10.5 MM (.35 - .41")
89128 10.5-12 MM (.41 - .47")
89129 12-14 MM (.47 - .55")
89130 14-16 MM (.55 - .63")
89131 16-18 MM (.63 - .71")
89132 18-20 MM (.71 - .79")
89133 20-22 MM (.79 - .87")
89134 22-24 MM (87 - .94")
89135 24-26 MM (.94 - 1.02")
89136 26-28 MM (1.02 - 1.10")
(Loc F) CABLE SEAL PLUGS (6-28 MM)
89085 6-7.5 MM (.23 - .29") 10/PK
89086 7.5-9 MM (.29 - .35") 10/PK
89087 9-10.5 MM (.35 - .41") 10/PK
89088 10.5-12 MM (.41 - .47") 10/PK
89093 12-14 MM (.47 - .55") 10/PK
89094 14-16 MM (.55 - .63") 10/PK
89095 16-18 MM (.63 - .71") 10/PK
89096 18-20 MM (.71 - .79") 10/PK
89103 20-22 MM (.79 - .87") 10/PK
89104 22-24 MM (.87 - .95") 10/PK
89105 24-26 MM (.95 - 1.02") 10/PK
89106 26-28 MM (1.02 -1.10") 10/PK
(Loc E) CABLE SEALS (6-28 MM)
89022 DUCT SEAL 1"
89042 DUCT SEAL 1.25"
89062 DUCT SEAL 1.50"
89072 DUCT SEAL 2"
(Loc B) DUCT SEALS (1.00-2.00") (I.D.)
Tornado Configuration Guide
D C or
Appendix 5