Document Outline

• Content
• 1 General Information 7
• 2 Equipment and Storage 9
• 3 Sensistor Sentrac Description 13
• 4 Hand Probe P60 17
• 5 System Examples 21
• 6 Setup 23
• 7 Menu System 25
• 8 Operating the Sensistor Sentrac 33
• 9 Recipes 43
• 10 Calibration 47
• 11 Info 51
• 12 Diagnosis 53
• 13 Troubleshooting 55
• 14 Maintenance Instructions 57
• 15 Service 63
• 16 Technical Data 65
• 17 Spare Parts and Accessories 73
• 18 Support from INFICON 75
• 19 Declaration of Conformity 77
• 20 Disposal 79
• 21 Appendix 81
  • General Safety Precaution
    • Warning
    • Warning
    • Warning
  • 1 General Information
• 1.1 About this manual
  • 1.1.1 Related Manuals
  • 1.1.2 Document History
• 1.2 Introduction to the Sensistor Sentrac
  • 1.2.1 Intended Use
  • 1.2.2 Available Models
    • 2 Equipment and Storage
      • Notice
• 2.1 Supplied Equipment Desktop Model
• 2.2 Supplied Equipment Portable Model
• 2.3 Peripheral Equipment
• 2.4 Storage
  • 3 Sensistor Sentrac Description
• 3.1 Front View
• 3.2 Rear View
• 3.3 Labels
  • 4 Hand Probe P60
• 4.1 General Information
• 4.2 Description
  • Notice
• 4.3 Calibration
  • 5 System Examples
• 5.1 Desktop Model
• 5.2 Portable Model
  • 6 Setup
    • Warning
• 6.1 Placement of the Sensistor Sentrac
• 6.2 Connect the Sensistor Sentrac
  • 1 Connect the probe to the Sensistor Sentrac using the probe cable. If you have purchased another type of probe than the Hand Probe P60, contact INFICON for help. It may require adaptation equipment between samples and instruments.
  • Notice
  • 7 Menu System
• 7.1 Menu Overview
• 7.2 Sensistor Sentrac Display
  • 7.2.1 Menu Navigation
    • Info Screen
    • Diagnosis Screen
  • 7.2.2 Menu Buttons
  • 7.2.3 Navigation and Other Buttons
• 7.3 Passwords
  • Notice
  • 8 Operating the Sensistor Sentrac
• 8.1 Preparation
  • Notice
  • 8.1.1 Battery Operation
    • Notice
      • 1 When battery is low, connect the battery charger.
  • 8.1.2 Conditions for Leak Detection
    • Notice
• 8.2 Settings
  • 8.2.1 How To Locate Leaks
    • Notice
  • 8.2.2 Performing Leak Detection
    • Notice
  • 8.2.3 How To Measure Leaks
    • Notice
  • 8.2.4 Performing Leak Measurement
    • Notice
• 8.3 Hands On
  • Notice
• 8.4 To Quantify Leaks
• 8.5 I·Guide
  • To use I·Guide
  • Measuring with Dynamic Measurement Points
  • 9 Recipes
    • Notice
• 9.1 Recipe Overview
• 9.2 Create a Recipe
  • 9.2.1 New Recipe
  • 9.2.2 Modify a Recipe
  • 9.2.3 Select an Existing Recipe
  • 9.2.4 Delete a Recipe
• 9.3 Probe Settings
• 9.4 General Settings
• 9.5 Communication Settings
  • USB and RS232
  • PLC Out
  • PLC In
  • Ana. Out
  • 10 Calibration
• 10.1 About Calibration
  • Notice
  • 10.1.1 When Needed?
    • Set Calibration Interval
      • Notice
  • 10.1.2 Required Equipment
• 10.2 How to Calibrate
  • 10.2.1 Prepare the Calibration Leak
    • Leak with container:
    • Leak without container:
  • 10.2.2 Set the Calibration Value
    • Example, Calibration Leak:
    • Example, Calibration Gas:
      • Notice
  • 10.2.3 Calibrate Procedure
    • Notice
    • 11 Info
• 11.1 Statistics
  • 11.1.1 Run Time
  • 11.1.2 Calibration
  • 11.1.3 I·Guide
• 11.2 Export/Import
  • 11.2.1 Export
  • 11.2.2 Import
• 11.3 Settings Overview
  • Notice
• 11.4 I/O
• 11.5 Show password
• 11.6 About
  • 12 Diagnosis
• 12.1 Warning
  • Notice
• 12.2 Service Screen
  • Notice
• 12.3 Reset
  • Notice
  • 13 Troubleshooting
• 13.1 Fault Symptoms
• 13.2 Hardware Error Messages
  • 14 Maintenance Instructions
    • Notice
• 14.1 Changing Fuses
  • Disassemble
  • Assemble
• 14.2 Changing Probe Tip Filter
• 14.3 Changing Probe Protection Cap
  • Notice
• 14.4 Changing Probe Sensor
  • Assemble
• 14.5 Software Update
  • 1 Download the update software to a computer.
  • Notice
  • Notice
  • Notice
  • 15 Service
  • 16 Technical Data
• 16.1 Interfaces and Connectors
  • Notice
  • 16.1.1 SD Card Slot
  • 16.1.2 USB Port
  • 16.1.3 Communication Port
    • Notes
  • 16.1.4 Connection Port
  • 16.1.5 Power Input (Desktop Model)
  • 16.1.6 Power Input (Portable Model)
    • 17 Spare Parts and Accessories
• 17.1 Spare Parts
• 17.2 Accessories
  • 18 Support from INFICON
• 18.1 How to Contact INFICON
• 18.2 Returning Components to INFICON
  • 19 Declaration of Conformity
  • 20 Disposal
  • 21 Appendix
• 21.1 Parameter Index