JUMO 902931 Wtrans Receiver with Wireless Data Transmission Operating Manual User Manual

Jumo wtrans receiver, With wireless data transmission

Advertising
background image

JUMO Wtrans Receiver

with Wireless Data Transmission

B 902931.0

Operating Manual

2013-02-14/00488966

Advertising
Table of contents

Document Outline

  • b90.2931.0en_2010-06-01.pdf
    • 1 Introduction
      • 1.1 Safety information
      • 1.2 Description
      • 1.3 Block diagram
    • 2 Identifying the instrument version
      • 2.1 Rating plate
      • 2.2 Type designation
      • 2.3 Serial accessories
      • 2.4 Accessories
    • 3 Basics
      • 3.1 Radio technology
      • 3.2 General information about radio transmission
      • 3.3 Reception characteristic of the lambda/4 antenna
      • 3.4 Interferences
      • 3.5 Function overview
      • 3.6 Data flow diagram
    • 4 Installation
      • 4.1 Installation site and climatic conditions
        • 4.1.1 Receiver
        • 4.1.2 Antenna
      • 4.2 Dimensions
        • 4.2.1 Receiver
        • 4.2.2 Lambda/4 antenna
        • 4.2.3 Antenna wall holder for lambda/4 antenna
      • 4.3 Receiver installation
      • 4.4 Fitting the antenna
        • 4.4.1 Antenna installation directly on the receiver
        • 4.4.2 Antenna installation on the antenna wall holder
    • 5 Electrical connection
      • 5.1 Installation notes
      • 5.2 Connection diagram
    • 6 Display and key functions
      • 6.1 Normal display (ND) (measured values and signal quality)
      • 6.2 Commissioning/start-up level (In) (allocating the probe ID to a channel)
      • 6.3 Parameter level (PA) (Parameter configuration)
      • 6.4 Light diodes (independent of level)
    • 7 Receiver operation
      • 7.1 Normal display (ND)
      • 7.2 Channels and their Display measured values
      • 7.3 Display signal quality of the probes received
      • 7.4 Changing to other Changing levels
      • 7.5 Code interrogation
    • 8 Configuration of the receiver
      • 8.1 Commissioning/start-up level (In)
        • 8.1.1 Selection of a transmitter ID from the link list and assignment to a channel
        • 8.1.2 Manual assignment of a transmitter ID to a channel
        • 8.1.3 Assignment of a transmitter ID to a channel via interface
        • 8.1.4 Pre-configuration of all transmitter ID's using the setup program
        • 8.1.5 Configuration of customized transmitter ID's on the transmitter side
      • 8.2 Parameter level (PA)
        • 8.2.1 Editing parameters
        • 8.2.2 General parameters
        • 8.2.3 Channel specific parameters
    • 9 Term definition
      • 9.1 General parameters
        • 9.1.1 device information
        • 9.1.2 Device data
        • 9.1.3 RS485 interface
        • 9.1.4 Analog outputs 1 to 4
        • 9.1.5 Relay outputs 1 to 2
        • 9.1.6 Modbus remote control values FLOAT 1 to 4
      • 9.2 Channel specific parameters
    • 10 Display and reset fly back
    • 11 Setup program
      • 11.1 General information about the setup program
      • 11.2 Hardware and software prerequisites
      • 11.3 Connect PC and receiver to each other
      • 11.4 Configuration of the receiver
        • 11.4.1 Establishing the communication
        • 11.4.2 Reading out the current receiver parameters
        • 11.4.3 Editing receiver parameters
        • 11.4.4 Transmit new parameters to the receiver
      • 11.5 Customer-specific linearization
      • 11.6 OnlineChart
    • 12 Detect and remedy faults/errors
    • 13 Supplement
      • 13.1 Technical data
      • 13.2 Table: Assignment of probes to the receiver channels
Popular Brands
Popular manuals