Document Outline

• b90.2931.0en_2010-06-01.pdf
  • 1 Introduction
    • 1.1 Safety information
    • 1.2 Description
    • 1.3 Block diagram
  • 2 Identifying the instrument version
    • 2.1 Rating plate
    • 2.2 Type designation
    • 2.3 Serial accessories
    • 2.4 Accessories
  • 3 Basics
    • 3.1 Radio technology
    • 3.2 General information about radio transmission
    • 3.3 Reception characteristic of the lambda/4 antenna
    • 3.4 Interferences
    • 3.5 Function overview
    • 3.6 Data flow diagram
  • 4 Installation
    • 4.1 Installation site and climatic conditions
      • 4.1.1 Receiver
      • 4.1.2 Antenna
    • 4.2 Dimensions
      • 4.2.1 Receiver
      • 4.2.2 Lambda/4 antenna
      • 4.2.3 Antenna wall holder for lambda/4 antenna
    • 4.3 Receiver installation
    • 4.4 Fitting the antenna
      • 4.4.1 Antenna installation directly on the receiver
      • 4.4.2 Antenna installation on the antenna wall holder
  • 5 Electrical connection
    • 5.1 Installation notes
    • 5.2 Connection diagram
  • 6 Display and key functions
    • 6.1 Normal display (ND) (measured values and signal quality)
    • 6.2 Commissioning/start-up level (In) (allocating the probe ID to a channel)
    • 6.3 Parameter level (PA) (Parameter configuration)
    • 6.4 Light diodes (independent of level)
  • 7 Receiver operation
    • 7.1 Normal display (ND)
    • 7.2 Channels and their Display measured values
    • 7.3 Display signal quality of the probes received
    • 7.4 Changing to other Changing levels
    • 7.5 Code interrogation
  • 8 Configuration of the receiver
    • 8.1 Commissioning/start-up level (In)
      • 8.1.1 Selection of a transmitter ID from the link list and assignment to a channel
      • 8.1.2 Manual assignment of a transmitter ID to a channel
      • 8.1.3 Assignment of a transmitter ID to a channel via interface
      • 8.1.4 Pre-configuration of all transmitter ID's using the setup program
      • 8.1.5 Configuration of customized transmitter ID's on the transmitter side
    • 8.2 Parameter level (PA)
      • 8.2.1 Editing parameters
      • 8.2.2 General parameters
      • 8.2.3 Channel specific parameters
  • 9 Term definition
    • 9.1 General parameters
      • 9.1.1 device information
      • 9.1.2 Device data
      • 9.1.3 RS485 interface
      • 9.1.4 Analog outputs 1 to 4
      • 9.1.5 Relay outputs 1 to 2
      • 9.1.6 Modbus remote control values FLOAT 1 to 4
    • 9.2 Channel specific parameters
  • 10 Display and reset fly back
  • 11 Setup program
    • 11.1 General information about the setup program
    • 11.2 Hardware and software prerequisites
    • 11.3 Connect PC and receiver to each other
    • 11.4 Configuration of the receiver
      • 11.4.1 Establishing the communication
      • 11.4.2 Reading out the current receiver parameters
      • 11.4.3 Editing receiver parameters
      • 11.4.4 Transmit new parameters to the receiver
    • 11.5 Customer-specific linearization
    • 11.6 OnlineChart
  • 12 Detect and remedy faults/errors
  • 13 Supplement
    • 13.1 Technical data
    • 13.2 Table: Assignment of probes to the receiver channels