Omnitron Systems Technology iConverter CWDM/X 2 and 4 Channel Single-Fiber MUX/DEMUX - Manual

iConverter CWDM/X
2 and 4 Channel Single-Fiber MUX/DEMUX
USER MANUAL
Product Overview
The
iConverter Single-Fiber Course Wave Division
MUX/DEMUX CWDM/X modules utilize a single-
fiber Common Port that aggregates two different
wavelengths from each dual fiber Channel Port. Each
fiber strand on the Channel Port supports a different
wavelength, one wavelength for transmit (Tx) and a
different wavelength for receive (Rx).
Single-Fiber CWDM/X modules are always used in
pairs (example: model 8870-0 used with 8871-0). The transmit wavelength of the Channel
Port at one end must match the receive wavelength of the same Channel Port at the other
end, and the receive wavelength of the Channel Port at one end must match the transmit
wavelength of the same Channel Port at the other end.
Each channel on the Common Port consists of two wavelengths, a transmit and a receive
as shown in Figure 1.
Figure 1: A Pair of 2-Channel MUX/DEMUX Modules
2-Channel CWDM/X modules support four wavelengths; two transmit and two receive.
4-Channel Single-Fiber CWDM/X modules support eight wavelengths. Up to 8 channels
(sixteen wavelengths) are supported by combining two CWDM/X modules with an iConverter
Band Splitter (8865-0). For more information, access Omnitron’s web page to view all
relevant documents:
http://www.omnitron-systems.com/cwdm_multiplexers.php
Model Numbers
Model Type
Model
Number
Channel Port
ITU Center Wavelength (nm)
Tx/Rx
2-Channel
MUX/DEMUXw
8870-0 1471/1491, 1511/1531
8871-0 1491/1471, 1531/1511
8872-0 1551/1571, 1591/1611
8873-0 1571/1551, 1611/1591
4-Channel
MUX/DEMUXw
8874-0 1271/1291, 1311/1331, 1351/1371, 1431/1451
8875-0 1291/1271, 1331/1311, 1371/1351, 1451/1431
8876-0 1471/1491, 1511/1531, 1551/1571, 1591/1611
8877-0 1491/1471, 1531/1511, 1571/1551, 1611/1591
s Single-fiber CWDM/X models must be used in pairs. The Tx wavelengths on one end have to match the Rx
wavelengths on the other.
Warranty
WARNING
The operating description in this Instruction Manual is for use by qualified personnel only. To avoid electrical shock, do not perform any
servicing of this unit other than that contained in the operating instructions, unless you are qualified and certified to do so by Omnitron
Systems Technology.
Warranty
This product is warranted to the original purchaser against defects in material and workmanship for a period of ONE YEAR from the date
of shipment. You may register your product on the Internet at http://www.omnitron-systems.com. During the warranty period, Omnitron
will, at its option, repair or replace a product which is proven to be defective.
For warranty service, the product must be sent to an Omnitron designated facility, at Buyer’s expense. Omnitron will pay the shipping
charge to return the product to Buyer’s designated US address using Omnitron’s standard shipping method.
Limitation of Warranty
The foregoing warranty shall not apply to defects resulting from improper or inadequate use and/or maintenance of the equipment by
Buyer, Buyer-supplied equipment, Buyer-supplied interfacing, unauthorized modifications or tampering with equipment (including removal
of equipment cover by personnel not specifically authorized and certified by Omnitron), or misuse, or operating outside the environmental
specification of the product (including but not limited to voltage, ambient temperature, radiation, unusual dust, etc.), or improper site
preparation or maintenance.
No other warranty is expressed or implied. Omnitron specifically disclaims the implied warranties of merchantability and fitness for any
particular purpose.
Exclusive Remedies
The remedies provided herein are the Buyer’s sole and exclusive remedies. Omnitron shall not be liable for any direct, indirect, special,
incidental, or consequential damages, whether based on contract, tort, or any legal theory.
040-08870-001B 11/09
Page 1
Omnitron Systems Technology * 140 Technology Dr. #500 * Irvine, CA 92618
949.250.6510 tel * 949.250.6514 fax * www.omnitron-systems.com