Omnitron Systems Technology FlexPoint 10FL/T User Manual

Omnitron Systems Technology Communication

Advertising

FlexPoint

™

10FL/T User Instructions

ABOUT THIS MANUAL:
This document supports revision “Rev. 2” of the 10FL/T.

Please refer to the serial number label on the bottom

of the 10FL/T for the revision number of your product.

This revision incorporates the following improvements

to the 10FL/T:
1. 10FL/T operates in Link Propagate mode: A port of

the 10FL/T transmits a Link signal only when receiving

a Link at the other port.
DESCRIPTION:
The Omnitron FlexPoint 10FL/T media converter pro-

vides 10BASE-FL single-mode (SM) or multimode (MM)

fiber to 10BASE-T twisted pair (UTP) media conversion.

The 10FL/T is compliant with the IEEE 802.3 standards.
It features a pair of ST or SC fiber connectors and an

EIA/TIA 568 RJ45 UTP connector.
These FlexPoint 10FL/T models are supported:
Model Fiber Type

Max Distance Connector

4300 850 nm (MM)

2 km

4301 1310 nm (SM) 30 km

4302 1310 nm (MM) 5 km

4303 850 nm (MM)

2 km

4304 1310 nm (SM) 30 km

4306 1550 nm (SM) 85 km

4307 1550 nm (SM) 120 km

For other fiber configurations, please consult factory.

The 10FL/T automatically supports Half-Duplex and Full-

Duplex operations. It also supports switch-selectable

straight-through or crossed RJ45 UTP wiring.
POWER ADAPTER NOTICE:
1. When used in a standalone configuration, this product

is intended to be used only with a Listed Direct Plug-In

Power Unit marked “Class 2” and rated at 9Vdc, 1 Amp.
2. This product should always be used only with

Omnitron Supplied Power Unit model number 9113-PS

or 9115-PS.

MOUNTING:
The FlexPoint 10FL/T can be solo-mounted using a wall-

mounting kit or DC Power Adapter. It can also be rack-

mounted using a 5-position shelf, or a 14-position, high-

density FlexPoint Powered Chassis. If wall-mounting or

shelf-mounting, attach the power adapter unit.
Attach the fiber cables to the FlexPoint 10FL/T ST or

SC connectors. Note that the FlexPoint transmit (Tx)

must attach to the receive side on the device at the far

end of the fiber and the receive (Rx) must attach to the

transmit side.
Both the fiber and UTP ports must be connected in order

for the unit to establish an end-to-end link.

DIP-SWITCH SETTINGS:

UTP Crossover DIP-Switch:
When connecting the UTP cable to a hub or switch,

set the DIP-switch to straight-through

“UTP Hub/

Switch” (factory setting). When connecting to a PC

or workstation, set the DIP-switch to crossover

“UTP

to Workstation”.
Disable Auto-Negotiation and manually set port

speed to 10Mbps on the connecting UTP device.
LED INDICATORS:
LED

Color Description

Power On

Yellow Power applied

Polarity

Yellow Polarity reversal was detected

and corrected automatically

Fiber Link

Green Operational device detected at

the far end of fiber

Fiber Rx

Green Received data on fiber line

UTP Link

Green Operational device detected at

the far end of UTP

UTP Rx

Green Received data on UTP link

TECHNICAL SUPPORT:

If you encounter problems in installing or maintaining this

product, contact Omnitron Technical Support:

Phone:

(949) 250-6510

Fax:

(949) 250-6514

Address: Omnitron Systems Technology, Inc.

38 Tesla

Irvine, CA 92618 USA

E-mail: [email protected]

URL:

http://www.omnitron-systems.com

User W

arranty Registration

Please register on-line @

http://www

.omnitron-systems.com

or complete both

sides and mail or fax this registration form to:

Omnitron Systems T

echnology

, Inc.

38 T

esla

Irvine, CA

92618 USA

Fax: (949) 250-6514

Name:___________________________________________________

Company:_______________________________________________

Address:_______________________________________________

_______________________________________________

City: ___________________ State: _______ Zip Code: __________

Country:________________________________________________

Phone:

____________________

Fax:

_________________________

E-mail:__________________________________________________

Please complete both sides of this form

WARNING!

Before inserting the Power Adapter, verify

that the power on the unit is appropriate for

your AC line voltage source.

User W

arranty Registration

Please register on-line @

http://www

.omnitron-systems.com

or complete both

sides and mail or fax this registration form to:

FlexPoint T

ype:



10FL/T



10FL/2



10T/2



Other _______

Model:

_________________________________________________

Serial Number: ______________ Purchase Date:

______________

Purchased From: _________________________________________

Address:

______________________________________________

City: ___________________ State: _______ Zip Code:

Country:

_______________________________________________

Comments and Suggestions:

_______________________________

______________________________________________________

Please complete both sides of this form

Warning

The operating description in this Instruction Manual is

for use by qualified personnel only. To avoid electrical

shock, do not perform any servicing of this unit other than

that contained in the operating instructions, unless you

are qualified and certified to do so by Omnitron Systems

Technology, Inc.

Caution

All user-required operations can be performed without

opening the unit. Never attempt to open or remove the

cover or tamper with the unit.

Warranty

This product is warranted to the original purchaser

against defects in material and workmanship for a period

of TWO YEARS from the date of shipment. A LIFETIME

warranty may be obtained by the original purchaser by

REGISTERING this product with Omnitron within 90 days

from the date of shipment. TO REGISTER, COMPLETE

AND MAIL OR FAX THE REGISTRATION PORTION OF

THIS INSTRUCTION MANUAL TO THE INDICATED

ADDRESS. Or you may register your product on the

internet at http://www.omnitron-systems.com. During

the warranty period, Omnitron will, at its option, repair

or replace a product which is proven to be defective.
For warranty service, the product must be sent to

an Omnitron designated facility, at Buyer’s expense.

Omnitron will pay the shipping charge to return the

product to Buyer’s designated US address using

Omnitron’s standard shipping method.

Limitation of Warranty

The foregoing warranty shall not apply to defects

resulting from improper or inadequate use and/or

maintenance of the equipment by Buyer, Buyer-supplied

equipment, Buyer-supplied interfacing, unauthorized

modifications or tampering with equipment (including

removal of equipment cover by personnel not specifically

authorized and certified by Omnitron), or misuse, or

operating outside the environmental specification of the

product (including but not limited to voltage, ambient

temperature, radiation, unusual dust, etc.), or improper

site preparation or maintenance.
No other warranty is expressed or implied. Omnitron

specifically disclaims the implied warranties of

merchantability and fitness for any particular purpose.

Exclusive Remedies

The remedies provided herein are the Buyer’s sole and

exclusive remedies. Omnitron shall not be liable for

any direct, indirect, special, incidental, or consequential

damages, whether based on contract, tort, or any legal

theory.

Notes:

____________________________

_____________________________

____________________________

Form: 040-04300-003G 10/13

Advertising

Popular Brands

Popular manuals