8 cleaning, wear and service, Cleaning, wear and service, 1 cleaning – Retsch Cryomill User Manual
Page 51: 2 wear, 3 wearing parts, Caution, 4 service
Cleaning, wear and service
51
Pos : 9. 2 / 00005 Übersc hrift en/1. Übersc hrift en/1 Rei nigung, Versc hleiß und Wart ung @ 0\ mod_1228989974062_9.doc @ 4948 @ @ 1
8 Cleaning, wear and service
Pos : 9. 3 / 00005 Übersc hrift en/1. 1 Ü berschrif ten/ 1. 1 Ü bers chrift en BDA/ 11 R einigung @ 0 \ mod_1226909670239_9. doc @ 3607 @ @ 1
8.1 Cleaning
Pos : 9. 4 / 00010 Bedienungsanlei tungen Kapit elsamml ung en/Cr yoMill I I/ 0010 Rei nigung Wart ung Verschl eiß/ 0001 Cr yoMill II M odul R einigung @ 5\ mod_1343830765834_9. doc @ 33488 @ @ 1
Fig. 49: Pulling out the condensation collecting filter
The condensation collecting filter must be cleaned regularly depending on the
ambient conditions, the degree of use and the general air humidity.
•
Pull out the condensation collecting filter (R).
•
Clean the condensation collecting filter under running water with a little
standard washing up liquid.
•
Allow the collecting filter to dry and then insert in the device again.
Pos : 9. 5 / 00005 Übersc hrift en/1. 1 Ü berschrif ten/ 1. 1 Ü bers chrift en BDA/ 11 Versc hleiß @ 0\ mod_1226909713106_9. doc @ 3619 @ @ 1
8.2 Wear
Pos : 9. 6 / 00010 Bedienungsanlei tungen Kapit elsamml ung en/Cr yoMill/ 0010 Rei nigung Wart ung Verschl eiß/ Gener al M odul Versc hleiß teil e @ 0\ mod_1226910875207_9. doc @ 3697 @ @ 1
The grinding tools may become worn, depending on the frequency of the grinding
operation and the sample material. The grinding jars and the balls should be
regularly checked for wear and replaced if necessary.
Pos : 9. 7 / 00005 Übersc hrift en/1. 1 Ü berschrif ten/ 1. 1 Ü bers chrift en R ep/11 R ep Versc hleißt eile @ 0\ mod_1226909806428_9. doc @ 3631 @ @ 1
8.3 Wearing parts
Pos : 9. 8 / 00004 War nhi nweis e/ V0013 VORSICHT R eparatur en @ 0\ mod_1232443088492_9. doc @ 5530 @ @ 1
CAUTION
Personal injury
Incorrect repairs
–
This operating manual does not include instructions for repair.
•
For your own safety repairs should be carried out only by Retsch
GmbH or an authorised representative (service technicians).
Pos : 9. 9 / 00005 Übersc hrift en/1. 1 Ü berschrif ten/ 1. 1 Ü bers chrift en BDA/ 11 Wartung @ 0\ mod_1226909694066_9. doc @ 3613 @ @ 1
8.4 Service
Pos : 9. 10 /00010 Bedi enungsanleit ung en Kapitels ammlungen/Cr yoMill/0010 R ei nigung Wartung Versc hleiß /G ener al Modul Wart ung @ 0\ mod_1226910835081_9.doc @ 3691 @ @ 1
R