Barco R9001769 - Manual (Page 16)

5-2
Connections
5976069 BARCOREALITY 6400 14032000
Switching to Stand-by.
When the projector is running and you want to go to stand-by, press the stand-by key for 2 seconds until the message 'Saving data, please
wait' is displayed. Do not press any longer on the standby key otherwise the projector will restart.
Switching Off
To switch off:
- First press STANDBY key for 2 seconds. When the message 'Saving data, please wait' is displayed, do not press any longer on the standby
key otherwise the projector will restart. Let cool down the projector at least 10 min.
- Switch off the projector with the power switch.
Switching to Stand-by Warning
When switching to standby, it is possible to restart within the first 5sec.. When not restarted within these first 5 sec., the
projector waits for 1 min. to restart again. During this period the LED display will show a jumping square with a dash. After
one minute, two dashes will be displayed and the projector can restart.
Input Connections
Input facilities : Video
S-Video
5-cable input
Computer
Serial digital input
IEEE 1394 (not yet active)
Input Selection :
This can be manually or automatically.
When 'automatic' is selected in the Input slots menu, by starting up the projector, it searches for an input source by scanning the inputs one
by one. If only one source is found, this source will be projected. If different sources are found, the priority is as follow :
1. Video
2. S-Video
3. 5 Cable input
4. Computer input
SDI input and IEEE input are never automatically selected.
Note : When a RCVDS is connected to the projector,
the 'Automatic' selection is disabled.
Set up of the input selection :
1 Press ENTER to start up the adjustment mode.
2 Press the cursor key é or ê to select 'Installation'.
3 Press ENTER to display the Installation menu.
4 Press the cursor key é or ê to select 'Input Slots'.
5 Press ENTER to display the Input slots menu.
6 Press the cursor key é or ê to select 'Input Slots'.
7 Press ENTER to toggle between [Manual] or [Automatic].
8 Press EXIT several times to leave the adjustment mode.
Lamp Run Time
When the total run time of the lamp is X-30 hours or more, the following warning message
will be displayed for 1 minute. This warning message will be repeated every 30 minutes.
Press EXIT to remove the message before the minute is over.
When the total run time of the lamp is 500 hours or more, the following warning message,
with the exact run time is displayed on the screen.
Lamp run time is X hours. Operating the lamp longer than X hours may damage the
projector. Please replace the lamp.
When OK (ENTER) is pressed to go on, the warning will be repeated every 30 min.
The total lifetime of the lamp for a safe operation is X hours max. Do not use it longer. Always
replace with a same type of lamp. Call a BARCO authorized service technician for lamp
replacement.
Lamp Run Time Warning
Using a lamp for more than X hours is dangerous as the lamp could
explode.
Remaining
Lamp run time
20 h
<ENTER> to continue
WARNING
Lamp run time is X hours
Operating the lamp longer
than X hours may damage
the projector.
Please replace the lamp
Select with or
then <ENTER>
<EXIT> to return.
Select with or
then <ENTER>
<EXIT> to return.
INSTALLATION
INPUT SLOTS
ADJUSTMENT MODE
Select a path from below :
RANDOM ACCESS
INSTALLATION
Saving data, Please wait
INPUT SLOTS
SLOT SELECTOR [Automatic]
x 1. RGB [HS&VS]
- 2. RGB [HS&VS]
x 3. VIDEO
- 4. S-VIDEO
- 5. DIGITAL INPUT
- 6. IEEE 1394
Select with or
<ENTER> to toggle
<EXIT> to return.