Viking Pump TSM635.3: Q-QS Universal Mag Drive - Manual (Page 5)

54 59 65
66
57 46 47 45
44
43
40
63 35 38 39 37 36
60A
60 31
52 51
33 67
25
60A
60
13 62
6 4 1
2 5 3
14 7A 7 8 28 28A 12 27
6
5 58
SECTION TSM 635.3 ISSUE C PAGE 5 OF 13
ITEM NAME oF PART ITEM NAME oF PART ITEM NAME oF PART
13 Capscrews for Adaptor Plate (8-Req’d) 40 Head and Idler Pin Assembly 57 Inner Magnet Assembly
25 Adaptor Plate Bushing 43 Studs for Head (8-Req’d) 59 Canister
31 Casing 44 Nuts for Head (8-Req’d) 60 Thrust Washer - Rotating (2-Req’d)
33 Adaptor Plate O-Ring 45 Relief Valve Gaskets (2-Req’d) 60A Thrust Washer - Stationary (2-Req’d)
35 Head O-Ring 46 Capscrews for Relief Valve (8-Req’d) 62 Key for Rotor Shaft
36 Rotor and Shaft Assembly 47 Relief Valve 63 Shims for Head
37 Idler and Bushing Assembly 51 Studs for Flanges (16-Req’d) 65 Canister O-Ring
38 Idler Bushing 52 Nuts for Flanges (16-Req’d) 66 Split Locknut
39 Idler Pin 54 Capscrews for Canister (8-Req’d) 67 Adaptor Plate
ITEM NAME oF PART ITEM NAME oF PART ITEM NAME oF PART
1 Locknut 6 Tapered Roller Bearing (2-Req’d) 14 Capscrews for Disassembly (3-Req’d)
2 Lockwasher 7 Bearing Housing 27 Bracket
3 End Cap 7A Capscrews for Bearing Housing (6-Req’d) 28 Capscrews for Mounting Bracket (2-Req’d)
4 Outer Bearing Spacer 8 Inner Bearing Spacer 28A Capscrews for Bracket (2-Req’d)
5 Lipseal (2-Req’d) 12 Grease Fitting 58 Outer Magnet Assembly
FIGURE 6
ExPLoDED VIEW – UNIVERSAL MAG DRIVE PUMP CANISTER THRoUGH RELIEF VALVE
FIGURE 7
ExPLoDED VIEW – UNIVERSAL MAG DRIVE PUMP BRACKET AND oUTER MAGNET ASSEMBLY
PUMP DISASSEMBLY
WARNING!
Refer to DANGER & CAUTIoN listed on page 2
before proceeding.
NoTE: Some steps require a second person for ease
of disassembly.
1. Drain the liquid being pumped by removing the two
drain plugs (if present). Both are located in the bottom
of the casing. Once the liquid has drained, replace the
plugs.
2. Refer to Figures 6 and 7 for the names of parts.
3. Use a non-magnetic surface to disassemble the pump.
4. Mark the head (40) and casing (31) before disassembly
to insure proper reassembly.
5. To inspect the head and pin assembly (39 and 40) and
idler and bushing assembly (37 and 38), remove the
head nuts (44).
6. Remove the head from the pump. Tilt the top of the
pump head back during removal to prevent the idler
from falling off the idler pin. If the casing was not
drained in Step 1, be careful of the liquid draining out
between the head and casing. Avoid damaging the
head shim set (63) since all shims are required to
maintain end clearance. Inspect the O-ring (35). Do
not remove the O-ring from the plate adaptor / casing