Great Plains ADC2250 Operator Manual - Manual (Page 30)

28
Section 3 Adjustments
Model 2250 Air Drill Cart 167-033M 7/28/10
Great Plains Mfg., Inc.
Flax Seed Rate Chart
Unknown Variety - 49.5 Lbs/Bu
Seed
Rate
Quick Change
Sprocket
(See Figure 3-6)
Driving/Driven Gears
(See Figure 3-1)
Gearbox
Shift
Levers
(See
Figure 3-3)
Seed
Rate
Quick Change
Sprocket
(See Figure 3-6)
Driving/Driven Gears
(See Figure 3-1)
Gearbox
Shift
Levers
(See
Figure 3-3)
Lbs/Acre Driving 1 Driven 2 Driving 3 Driven 4 Lbs/Acre Driving 1 Driven 2 Driving 3 Driven 4
1.5 20 30 17 54 E5 21.3 20 30 54 17 E5
1.8 20 30 17 54 D5 24.3 20 30 54 17 D5
2.0 20 30 17 54 E4 26.5 20 30 54 17 E4
2.2 20 30 17 54 C5 28.2 20 30 54 17 C5
2.4 20 30 17 54 D4 30.2 20 30 54 17 D4
2.6 20 30 17 54 E3 31.6 20 30 54 17 E3
2.8 20 30 17 54 B5 33.7 20 30 54 17 B5
3.0 20 30 17 54 C4 35.0 20 30 54 17 C4
3.1 20 30 17 54 D3 36.0 20 30 54 17 D3
3.1 20 30 17 54 E2 36.7 20 30 54 17 E2
3.7 20 30 17 54 E1 41.6 20 30 54 17 E1
3.7 20 30 17 54 D2 41.6 20 30 54 17 D2
3.7 20 30 17 54 C3 41.6 20 30 54 17 C3
3.7 20 30 17 54 B4 41.6 20 30 54 17 B4
3.7 20 30 17 54 A5 41.6 20 30 54 17 A5
4.3 20 30 17 54 D1 47.1 20 30 54 17 D1
4.5 20 30 17 54 C2 48.1 20 30 54 17 C2
4.6 20 30 17 54 B3 49.3 20 30 54 17 B3
4.8 20 30 17 54 A4 51.2 20 30 54 17 A4
5.2 20 30 17 54 C1 54.3 20 30 54 17 C1
5.5 20 30 17 54 B2 56.8 20 30 54 17 B2
5.9 20 30 17 54 A3 60.5 20 30 54 17 A3
6.4 20 30 17 54 B1 64.1 20 30 54 17 B1
7.1 20 30 17 54 A2 69.5 20 30 54 17 A2
8.2 20 30 17 54 A1 78.2 20 30 54 17 A1
4.3 30 20 17 54 E5 46.5 30 20 54 17 E5
5.0 30 20 17 54 D5 52.6 30 20 54 17 D5
5.5 30 20 17 54 E4 57.1 30 20 54 17 E4
5.9 30 20 17 54 C5 60.5 30 20 54 17 C5
6.4 30 20 17 54 D4 64.4 30 20 54 17 D4
6.8 30 20 17 54 E3 67.3 30 20 54 17 E3
7.3 30 20 17 54 B5 71.3 30 20 54 17 B5
7.6 30 20 17 54 C4 73.9 30 20 54 17 C4
7.8 30 20 17 54 D3 75.8 30 20 54 17 D3
8.0 30 20 17 54 E2 77.2 30 20 54 17 E2
9.3 30 20 17 54 E1 86.8 30 20 54 17 E1
9.3 30 20 17 54 D2 86.8 30 20 54 17 D2
9.3 30 20 17 54 C3 86.8 30 20 54 17 C3
9.3 30 20 17 54 B4 86.8 30 20 54 17 B4
9.3 30 20 17 54 A5 86.8 30 20 54 17 A5
10.7 30 20 17 54 D1 97.5 30 20 54 17 D1
10.9 30 20 17 54 C2 99.2 30 20 54 17 C2
11.2 30 20 17 54 B3 101.7 30 20 54 17 B3
11.7 30 20 17 54 A4 105.3 30 20 54 17 A4
12.5 30 20 17 54 C1 111.4 30 20 54 17 C1
13.2 30 20 17 54 B2 116.2 30 20 54 17 B2
14.2 30 20 17 54 A3 123.4 30 20 54 17 A3
15.1 30 20 17 54 B1 130.6 30 20 54 17 B1
16.6 30 20 17 54 A2 141.4 30 20 54 17 A2
19.0 30 20 17 54 A1 159.7 30 20 54 17 A1
1 Connected to the gearbox output shaft. 2 Connected to the meter input shaft. 3 Located on the front/upper shaft of the meterbox. 4 Located on the lower/back shaft of the meterbox