Qmark WPC1500 - Portable Panel Heater - Manual (Page 2)

Specifications
PROdUCT FEATURES
1 The heater can either be free-standing or wall-mounted to
meet different user requirements.
2 Steel finned heating element heats quickly and efficiently.
3 3 wattages: 500W/1000W/1500W, choose the right wattage to
meet comfort needs and save energy.
4 Equipped with thermostat for precise temperature control.
5 Equipped with overheat and tip-over protective devices for
safe operation.
UNPACkING
After unpacking unit, inspect carefully for any damage that may
have occurred during transit. Shipping damage claim must be
filed with carrier. please make note of the model number and
date code for future reference.
ASSEMbly ANd INSTAllATION INSTRUCTIONS
1. If the heater is to be used as a free standing unit, support
legs must be attached. Remove the two legs from the acces-
sory box. Lay the heater on the floor, insert the two legs into
the rectangle holes on the left and right sides near the ends
of the heater bottom making sure to fit the 4 clips of each leg
into the holes (see Figure 1). press firmly to securely snap
into place (a small flat screwdriver may be required to secure
clips). After both sides are fitted, stand the heater upright on
the wheels and proceed to OpERATION.
2. For wall mounting applications, omit Step 1 above. Use
appropriate fasteners and drill 2 holes in the desired location,
15-3/4” apart, center to center, so that the heater bottom is
about 20” from the floor. Allow the fasteners to extend at least
1/4” from the wall and fit the keyhole slots in the heater back
onto the fasteners (see Figure 2). make sure the heater is
secure.
3. This heater is for use on 120 volts. The cord has a plug as
shown at A (Figure 3). An adapter as shown at C is available
for connecting three-blade grounding-type plugs to two-slot
receptacles. The green grounding lug extending from the
adapter must be connected to a permanent ground such as a
properly grounded outlet box. The adapter should not be
used if a three-slot grounded receptacle is available.
OPERATION INSTRUCTIONS
Wattage selection
Select wattage according to room size and ambient temperature.
The upper knob on the control panel is the wattage adjustment
knob; “I, II, III, Iv” refer to “0W, 500W, 1000W, 1500W” respec-
tively.
Temperature adjustment
The lower knob on the control panel is used to preset tempera-
ture: turn the knob from “low” to “high” clockwise
to increase temperature. When the temperature reaches the pre-
set temperature on the thermostat, the heating element will turn
off. To find a comfortable setting, start by turning the thermostat
to High and once the room temperature reaches the desired
temperature, reduce the thermostat until there is an audible
click, signaling the thermostat has turned off the element. The
thermostat will maintain this comfort level.
Your heater includes an additional light feature for safety. The red
warning light is located above the heater operation light (amber)
I
II III
IV
Low High
Wattage
Selection Knob
Amber
Indicator
Light
(Power On)
Temperature
Selection Knob
Red
Warning
Light
(Overheat)
Model Volts Watts Amps
WpC1500 120 500/1000/1500 4.2/8.3/12.5
Figure 1
Figure 4
Figure 3
Grounding Pin
Grounding Means
Cover of Grounded
Outlet Box
Metal
Screw
a CAUTION !
THE ILLUmINATED RED INDICATOR LIGHT SIGNIFIES THE
HEATER HAS BEEN SUBjECTED TO SOmE ABNORmAL
CONDITION. CHECK HEATER TO INSURE THAT IT HAS NOT
BEEN BLOCKED IN ANY mANNER (IF SO, REmOvE BLOCK-
AGE). IF THERE IS NO INDICATION OF BLOCKAGE, IT IS
RECOmmENDED THE HEATER BE CHECKED BY A REp-
UTABLE ELECTRICIAN OR REpAIR SERvICE TO INSURE
THE HEATER HAS NOT BEEN DAmAGED.
Figure 2
Keyhole Slots
A
B
C
Fourth hole from end