Sony MHC-331 - Manual (Page 17)

Recording a CD:
Specifying Track
Order (program edit)
You can adjust the total recording time to
the tape length while making a program.
Use the buttons on both the unit and the
remote to do this operation.
1
Press FUNCTION repeatedly until
"CD" appears in the display.
2
Press ^ OPEN / CLOSE and place a CD.
Then, press ^ OPEN/CLOSE again to
close the disc tray.
If the button for the disc tray containing
the CD you want to record is not lit
green, press DISC SKIP EX-CHANGE
repeatedly so that if lights green.
3
Press PLAY MODE repeatedly until
"PROGRAM" appears in the display.
4
Press DISC 1 - 3 to choose a CD.
5
Press or ^ on MULTI
CONTROLLER (or press or on
the remote) to choose a track.
6
Press ENTER/NEXT.
The chosen track number lights up in
the music calendar and is memorized. If
the track number disappears before you
press ENTER / NEXT, go back to step 5.
7
Repeat steps 5 and 6 from the same CD
and 4 to 6 from another CD to program
the remaining tracks you want to record
.on side A in the order you want them to
be recorded.
8 Press II on the remote to pause
recording at the end of side A.
"P" appears in the display. The total
playing time "0.00" is displayed.
9 Repeat steps 5 and 6 from the same CD
and 4 to 6 from another CD to program
the remaining tracks you want to record
on side B in the order you want them to
be recorded.
10
Press and insert a blank tape into
deck B with the side you want to record
on facing forward.
Recording will start from the front side
of the tape.
Make sure the tabs on the cassette have
not been removed.
11 Press II and then press # (O- is
linked and depressed at the same time)
on deck B.
Be sure to press the button firmly and
swiftly.
Deck B stands by for recording.
12
Press
II
on deck B again to release
recording pause.
Recording starts.
13
Press E>DD on the CD player.
The determined tracks for side A starts
playing and are recorded. After those
tracks have been recorded, the unit will
pause.
14
Set the tape to the beginning of side
B.
Take the tape out and insert the tape
with side B facing forward.
15
Press II and then press • (D> is
linked and depressed at the same time)
on deck B.
Be sure to press the button firmly and
swiftly.
Deck B stands by for recording.
16
Press II on deck B again to release
recording pause.
Recording starts.
17
Press CHIII on the CD player.
The determined tracks for side B starts
playing and are recorded.
To stop recording
Press B^ on deck B.
To check the order
Press CHECK on the remote repeatedly.
Each time you press CHECK, the number
of the programmed tracks appear in the
display.
To cancel program edit
Press PLAY MODE repeatedly until
"PROGRAM" disappears from the display.
To activate DOLBY NR
When you want to reduce the hiss noise in
low-level high-frequency signals, press
DOLBY NR so that "DOLBY NR B" appears
in the display after step 10.
Recording From the
Radio
You can record from the tuner onto a tape.
Use TYPE I (normal) or TYPE II (Cr02)
tape.
POWER-^ON
® 1 =;-- r - _ j
L_J
o 1
P L,
i , J
1
4,5
DOLBY NR • O
1 Press B± and insert a blank tape into
deck B with the side you want to record
on facing forward.
Recording will start from the front side
of the tape.
Make sure the tabs on the cassette have
not been removed.
2
Press TUNER/BAND several times until
the desired radio band appears.
3
Tune in the radio station you want to
record. (See "Listening to the Radio", or
"Playing Preset Radio Stations" for
details.)
4
Press II and then press # (O- is linked
and depressed at the same time) on deck
B.
Be sure to press d\e button firmly and
swiftly.
_
Deck B stands by for recording.
continue to next page -»
Chapter 4: tiie Tape Player ^