Wilbur Curtis PCGT5 - Manual (Page 3)

Steps to Programming
Your Curtis Generation 3 cappuccino dispenser is Factory Pre‑Set for Optimum Performance. Programming for all models is identical except
where noted.
Entering the Programing Menus
Press and hold STOP/WASH for about ten [10] seconds. Display will
read Program Menus,(See Illustration).
Manual Dispense (Factory Default) ¹
Press  or > to go to Manual Dispense Select.
Press  to go to Manual Dispense Select Station.
Choose the station and press, the display will read Saving Complete!
To select another station for manual dispense, press  to go to Manual
Dispense Select Station or press > to continue to the next menu.
Dispense By Time ²
The next screen is Dispense By Time < Select >. Press  to select a station. Select the station and the screen will read To Begin Press Push.
Press desired dispense button. Hot water will start to dispense and screen will display To Finish Press Push. When Push is pressed, time will be
saved and you will exit back to Dispense by Time screen. Continue with additional selections or press > to continue to the next menu.
Temperature (Factory set at 190°F – Cold Cappuccino Units Set at 96ºF)
Press  and screen will show Tank Temperature. Temperature is programmable from 80°F to 204°F in 2-degree increments. Press < or > to go up
or down in degrees. Select desired temperature and then to set. Press > to continue to the next menu.
Powder % Ratio (Factory set at 60%) ³
Press  and the screen will display Powder % Ratio Select Station. Press desired station. Powder ratio is programmable from 0% (Hot Water) to
100%, in 5% increments. Press < or > to increase or decrease ratio and then press  to set. Press > to continue to the next menu.
The range of powder-to-water ratio has been expanded. Valves should not be field adjusted to change product strength.
Product strength adjustments should be done through programming on the front panel only.
Service Call (Phone number)
Press  to display number and press  change number or > to move places and EX to exit when complete This number will be displayed during
a Heating system SENSOR ERROR or a WATER ERROR. Press > to continue to the next menu.
Banner Name
Press  to display letters, press  to change letters or > to move places and EX to exit when complete.
This feature allows up to 14 letters to be programmed for company name or regional name. Programming all blanks disables Banner Name. If
programmed, Banner Name is displayed every 5 sec. on and off. Press > to continue to the next menu.
Model Select
Press  to select, < or > to select desired model (PC-1, 2, 3, 4, 5) . Press  to set and exit program mode.
Exit
Press  to select, exits program mode and returns unit to operation.
PROGRAMMING CONTROL BUTTONS
3
Unique Settings: Model PCGT3 with
Preset Dispense
¹ Manual Dispense (Set to OFF)
Press  or > to go to Manual Dispense Select.
Press  to go to Manual Dispense Select Station.
Choose the station and press, the display will read Saving Complete!
To select another station for manual dispense, press  to go to Manual
Dispense Select Station or press > to continue to the next menu.
² Dispense By Time
Factory Default: All LARGE set at 25 seconds. All MEDIUM set at 16 seconds. All SMALL set at 12 seconds
Dispense By Time < Select >. Press  to select a station. Select the station and the screen will read To Begin Press Push. Press desired
dispense button. Hot water will start to dispense and screen will display To Finish Press Push. When Push is pressed, time will be saved and
you will exit back to Dispense by Time screen. Continue with additional selections or press > to continue to the next menu.
³ Powder % Ratio (Factory set at 45%)
Press  and the screen will display Powder % Ratio Select Station. Press desired station. Powder ratio is programmable from 0% (Hot Water)
to 100%, in 5% increments. Press < or > to increase or decrease ratio and then press  to set. Press > to continue to the next menu.
Model Select is Not a Menu Item on PCGT3 with Preset Dispense