Yamaha HTR-5835 - Manual (Page 3)

IMPORTANT SAFETY INSTRUCTIONS
d) If the product does not operate normally by following
the operating instructions. Adjust only those controls
that are covered by the operating instructions as an
improper adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore the product to its normal
operation.
e) If the product has been dropped or damaged in any
way, and
f) Wdien the product exhibits a distinct change in perfor­
mance - this indicates a need for sen-nce.
20 Replacement Parts - WTien replacement parts are required,
be sure the ser\ice teclinician has used replacement parts
specified by the manufacturer or have the same
characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or other
hazards.
21 Safety Check - Upon completion of any service or repairs to
this product, ask the semce technician to perform safety
checks to determine that the product is in proper operating
condition.
22 Wall or Ceiling Mounting - The unit should be mounted
to a wall or ceiling only as recoinniended by the
manufacturer.
23
Heat - The product should be situated away from heat
sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s
attention to Article 820-40 of the NEC that provides
guidelines for proper grounding and, in particular, specifies
that the cable ground shall be connected to the grounding
system of the building, as close to the point of cable entr)’ as
practical.
24 Outdoor Antenna Grounding — If an outside antenna or
cable system is connected to the product, be sure the antenna
or cable system is grounded so as to provide some
protection against voltage surges and built-up static charges.
Article 810 of the National Electrical Code, ANSI.'NFPA 70.
provides information with regard to proper grounding of the
mast and supporting structure, grounding of the lead-m wire
to an antenna discharge unit, size of grounding conductors,
location of anteima discharge unit, connection to grounding
electrodes, and requirements for the grounding electrode.
EXAMPLE OF ANTENNA GROUNDING
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
- GROUND CLAMPS
PO'AER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 2M. PART K}
FCC INFORMATION (for US customers)
IMPORTANT NOTICE: DO NOT MODIFA' THIS
UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifieations not expressly approved by
Yamaha may void your authority, granted by' the FCC, to
use the product.
IMPORTANT; WTien connecting this product to
accessories and/or another product use only high quality
shielded cables, Cabie.'s supplied w'lth this product MUST
be used. Follow' all installation instructions. Failure to
follow instructions could void your FCC authorization to
use this product in the USA.
NOTE: This product has been tested and found to comply'
with the requirements listed m FCC Regulations. Part 15
for Class “B” digital devices. Compliance with these
requirements provides a reasonable level of assurance that
your use of this product in a residential environment will
not result in harmful interference with other electronic
devices.
This equipment generates.'uses radio frequencies and, if
not installed and used according to the instractions found
in the users manual, may' cause interference harmful to the
operation of other electronic devices.
Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this
product IS found to be the soitrce of interference, wdiich
can be determined by turning the unit “OFF” and “ON”,
please try' to eliminate the problem by using one of the
following measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient
the antenna. If the antenna lead-in is 300 ohm ribbon lead,
change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory'
results, please contact the local retailer authorized to
distribute this type of product, if you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park. CA
90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.