Toshiba D-VR610KU - Manual (Page 41)

Hints for Timer Recording
• If there is a power failure or this unit has been
unplugged for more than 30 seconds., the clock setting
and all timer programming will be lost.
• If a disc is not inserted or if a inserted disc is not
recordable (finalized DVD-RW/-R, finalized DVD+RW, a
fully recorded disc, etc.), "DVD" on the front panel
display flashes and timer recording cannot be
performed. In some cases, 0 will appear momentarily
around the start point as the unit attempts to record.
Please insert a recordable disc.
• If a cassette tape with an erase-protection tab is not in
the cassette compartment or there is no cassette tape in
the cassette compartment, "VCR" on the front panel
display flashes and timer recording cannot be
performed. Please insert a recordable cassette tape.
• If you press [TIMER SET] and turn on the unit while
either DVD or VCR is in timer standby mode, @
disappears. In this case, you cannot change the mode
between DVD and VCR. You cannot change any settings
using [SETUP] or edit discs.
• When all the timer recording is completed, flashes. To
play back or eject the recorded disc, press
[I/O ON/STANDBY] first, then select the recorded title and
press [PLAY ►], or [OPEN/CLOSE ^] to remove the disc.
• During timer recording or timer standby mode (0 will
appear), any operations on the unit will not be available.
To make these operations available, press [■ STOP] on
the front panel to cancel the timer recording or [TIMER
SET] to release timer standby mode (|§| will disappear).
• To cancel the timer standby mode, press [TIMER SET].
• When the starting and the ending time are the same,
"Exceeds 12 hours" appears and the program setting will
not be accepted.
• When the programmed starting and ending time are
earlier than the current time, the setting will not be
accepted.
• If the starting time is earlier and the ending time is later
than the current time, the recording will start right after
[TIMER SET] is pressed.
• The timer recording cannot be performed in DVD and
VCR at the same time. If you set 2 programming with the
same channel and time in both devices, the program
with a lower program number will be recorded.
The Priority of Overlapped Settings
This unit records the programs according to priority if the timer programmings are overlapped. The timer
programming set previously has priority.
A timer recording of lower priority will be canceled or start from the middle.
Check the overlapped timer programmings and change the priority If necessary.
When the starting time is the same:
A program set previously (PROG. A) has priority.
I When the starting time and the ending time
for each programs are different:
A program that has earlier start time has priority.
PROG.A |PR0G.B
The first 2 nr minutes (at the longest) will be cut off. The first 2 minutes (at the longest) will be cut off.
When the recording time is partially overlapped:
PROG. A will start after PROG. B is complete to
be recorded.
1
PROG.B 1 PROG.A
"........
The first 2 rrlinutes (at the longest) will be cut off.
É
When the recording time is entirely overlapped:
PROG.A will not be recorded.
Note for DVD recording
• When the recording time of 2 programs are overlapped, or
the end time of a program and the start time of another
program is the same, the first 2 minutes (at the longest) of
the subsequent program will be cut off.
• If the cut-off portion comes up to 3 minutes or more, this
program will be displayed with errors number E40 in the
timer programming list.
I
PROG.B 1
When the end time of the programming
currently being recorded and the start time
of the subsequent program are same:
The beginning of the PROG. B may be cut off.
PROG. A i
1 PROG. B
The first 2 minutes (at the longest) will be cut off.
EN '41