Futaba BR3000 Battery Checker - Manual (Page 2)

Battery Checker
BR-3000
Instruction Manual
Thank you for purchasing a BR-3000.
The BR-3000 can check the state of various battery
packs used as the power source of R/C receivers, etc.
Battery pack total voltage display and remaining
capacity (criteria) are displayed on a bar graph and in
%. The voltage of each cell of a lithium battery pack
can also be displayed.
To sufficiently display its performance and for safe
use, please read this manual before using the
BR-3000.
Functions of the BR-3000
The display functions of the BR-3000 are shown below. However, the functions that can be
displayed vary depending on the type of battery pack.
*The BR-3000 operates on the power supplied from the connected battery.
Usage Precautions
Name of Each Part/Connection Method
Usage Method
[Lithium battery pack]
The total voltage, remaining capacity (criteria), cell voltage, minimum cell voltage, maximum
cell voltage, and cell voltage difference of lithium battery packs can be checked by the
following method:
1 Connect the battery pack to the 8-pin connector.
2 Select the type of battery pack with the TYPE button. (LiPo LiFeLiIon)
[Nickel cadmium/nickel metal hydride battery pack]
The total voltage and remaining capacity (criteria) of nickel cadmium and nickel metal hydride
battery packs can be checked by the following method. However, each cell cannot be displayed.
1
Connect the battery pack to the 3-pin connector.
2
Select the cell number by pressing the CELL button matched to the connected
battery pack.
Never connect the battery in reverse.
• Reverse connection may damage the inside of the BR-3000.
Never get the BR-3000 wet.
• The BR-3000 houses precision electronic circuits which may malfunction if water or other solution
enters the case. If the BR-3000 should get wet, always send it for repair.
Do not connect a battery pack to the 2 connectors at the same time.
• The battery may short circuit and cause abnormal heating and sparking.
Do not use the BR-3000 by placing it on a combustible material.
• There is the danger of abnormal heating of the battery for some reason.
Do not store the BR-3000 within the reach of children.
Be careful not to cause a short circuit by pinching the cord of the battery pack.
• Shorting may cause abnormal heating or sparking of the battery.
●LCD display
●Balance connector (8-pin)
Connector for lithium battery packs.
*The “-“ side of the battery pack balance
connector connects to the GND terminal of
the BR-3000.
*Ordinary balance connectors can be
directly connected. However, it is
necessary to provide a conversion adaptor
by yourself for using packs that have
different connector such as split type.
●Ni-cd/MH connector (3-pin)
Connector for nickel cadmium/nickel
metal hydride battery packs.
*The “-“ side of the battery pack connector
connects to the matching terminal at the
top of the BR-3000. (The center is the “+”
terminal.)
●TYPE button
Selects the type of
connected battery
pack.
(Lithium only)
●MODE button
Used when switching the display mode. (Lithium only)
●CELL button
Used when selecting the display screen of each cell. (Lithium)
Selects the cell number of the connected battery pack. (Nickel
cadmium/nickel metal hydride)
V Total
2S
LiFe
V
Max-Min
2S 1S
LiFe
V
Max
2S
LiFe
V
Max
2S
LiFe
V
Min
1S
LiFe
TYPE
MODE
MODE
MODE
MODE
CELL
●Total voltage and
remaining capacity
(criteria) display
screen
●Cell voltage display
screen
●Cell voltage difference
(maximum-minimum)
display screen
●Maximum cell voltage
display screen
●Minimum cell voltage
display screen
*The display screen of each cell
can be switched by pressing the
CELL button.
*The remaining capacity display
is based on the selected cell
voltage.
*Select the type by pressing the TYPE button. If a
battery type different from the connected battery pack
was displayed, select the correct type with the TYPE
button. If the battery type is different, the remaining
capacity (criteria) will not be correctly displayed.
*The display mode can be switched
by pressing the MODE button.
(Cell number)
<Balance operation (lithium only)>
Balance operation automatically starts about 5 seconds after the battery is
connected. When the voltage difference between cells reaches 5mV or less,
balance operation ends and then the BR-3000 enters the sleep mode and “----“
appears on the screen.
*The sleep mode can be exited by button operation.
*When the balance operation continues even if about 30 minutes pass, confirm the
voltage of each cell. An internal cell might be defective.
*The remaining capacity (criteria) display is based on voltage at no load. Since it may differ largely from
actual remaining capacity according to the battery type, use it as a criteria only.
*From the standpoint of the battery characteristics, immediately after charging and discharging, the
remaining capacity display will change until the battery stabilizes. The voltage stabilizes about 30
minutes after charging and discharging.
In addition, because of the different discharge characteristics, when the specified capacity was checked
after use, a remaining capacity lower than the actual remaining capacity may be displayed even for the
same type of battery. Judge the remaining capacity with the stable state value as a criteria.
*When the remaining capacity (criteria) display reaches 20% or less, recharge the battery.
*When the remaining capacity (criteria) display exceeds 95%, since the battery is almost fully charged,
refrain from charging it. Overcharging will cause the battery to deteriorate.
<Battery Pack Care>
For safety and to extract maximum performance from the battery pack used, observe the
following points:
• Discharge and store the battery pack in accordance with the battery instruction manual.
• Do not discharge a battery more than 80%. (Remaining capacity no less than 20%)
• Use the specified charger to charge the battery pack.
CELL
V Total
5S Nixx
(Cell number)
*Select the cell number by pressing the CELL
button. If the cell number is different from that of
the connected battery, the remaining capacity
(criteria) will not be correctly displayed.
[BR-3000 Ratings]
• Applicable battery packs: (See the above.)
• Voltage display error: ±1.5%
• Display range
Total voltage: (Ni type) 4.0~17V, (Li type) 5~34V
Cell voltage: (Li type) 1.1~4.9V • Case size:
85x63x15mm (excluding projecting parts)
• Weight: 52.6g
• Operating temperature: -10~+45˚C
• Storage temperature: -20~+60˚C
Total voltage
Remaining capacity (criteria)
Cell voltage
Minimum cell voltage
Maximum cell voltage
Cell voltage difference
Li-Fe/Li-Po/Li-Ion
X
X
X
X
X
X
Ni-Cd/Ni-MH
X
X
---
---
---
---
Bar graph, % display
Each cell
Maximum-minimum
[Display Functions]
(X: Yes, ---: No)
Notes: Always read this manual before using the BR-3000.
Store this manual where it can be used at any time.
1M23N26001
©Copyright 2011. No part of this manual may be reproduced in any form without prior permission. The contents
of this manual are subject to change without prior notice. While this manual has been carefully written, there may
be inadvertent errors or omissions. Please contact our service center if you feel that any corrections or
clarifications should be made.
FUTABA CORPORATION Phone: +81 475 32 6982, Facsimile: +81 475 32 6983
1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba 299-4395, Japan
©FUTABA CORPORATION 2011, 7 (1)
The BR-3000 Battery Checker can only be used with the battery packs shown in
“Corresponding Battery Packs” below. It cannot handle batteries of other cell sizes and
types. The checker display is based on voltage. Since the voltage changes with the battery
itself and the ambient temperature, use the remaining capacity display as a criteria only.
Corresponding Battery Packs:
●Lithium ferrite Li-Fe (2~7 cells) ●Lithium polymer Li-Po (2~7 cells) ●Lithium ion Li-Ion
(2~7 cells) ●Nickel cadmium Ni-Cd (4~7 cells) ●Nickel metal hydride Ni-MH (4~7 cell)
(Specifications and ratings are subject to change without notice.)
Special Markings;
Pay special attention to the
safety at the parts of this
manual that are indicated
by the following marks.
Symbol:
; Prohibited
; Mandatory
Mark Meaning
Procedures which may lead to a dangerous
condition and cause death or serious injury to the
user if not carried out properly.
Procedures which may lead to a dangerous
condition or cause death or serious injury to the
user if not carried out properly, or procedures
where the probability of superficial injury or
physical damage is high.
Procedures where the possibility of serious injury
to the user is small, but there is a danger of injury,
or physical damage, if not carried out properly.
Do not use the BR-3000 near objects that may ignite.
• Ignition by sparking when the battery is connected and disconnected is extremely dangerous.
<When requesting repair>
Before requesting repair, read this instruction manual again and check the BR-3000. When
there is an abnormality, request repair to your local Futaba dealer.
*Buzzer display: When battery pack
connected, at button operation
*The remaining capacity
display is based on the
maximum cell voltage.
*The remaining capacity
display is based on the
minimum cell voltage.
Remaining capacity display