Futaba MPDX-1 - Manual (Page 3)

MPDX-1 setting
ｎ CAUTION
ｊ Always use the miniature screwdriver supplied
to operate the MPDX-1 rotary switch and push
switches.
*Do not apply excessive force while operating.
Operation mode setting
Set the operation mode to match the mode of the receiver used.
1 Set the rotary switch to the "G3/1024" position.
2 Switch the mode to match the type of receiver.
(PCM-G3, PCM1024, PPM mode).
*Each time the "INC/FS" (or "DEC/HOLD") push switch is
pushed for 1 second, the PCM-G3, PCM1014, and PPM
mode is alternately selected. When the LED is off, the
MPDX-1 is in the PCM-G3 mode, when the LED blinks
slowly, the MPDX-1 is in the PCM1024 mode, and when
the LED lights steadily, the MPDX-1 is in the PPM mode.
F/S mode/HOLD mode setting
7KHRSHUDWLRQPRGHRIHDFKVHUYRZKHQWKHUHFHLYHUFDQQRW
UHFHLYHVLJQDOVQRUPDOO\FDQEHVHW
F/S mode: Servo moves to a preset position.
HOLD mode: Servo remains in its present position.
1 Set the rotary switch to the "FS/SPEED" position.
2 Push the "INC/FS" (or "DEC/HOLD") push switch to
turn off the LED.
*Each time the push switch is pressed, the LED toggles
between off and slow blink.
3 Set the rotary switch to the channel # you want to
set to the F/S mode or HOLD mode.
When you want to set the channel to the F/S mode, move
the servo to the F/S operation position at the transmitter
side and push the "INC/FS" switch.
*When setting is complete, the LED lights.
When you want to set the channel to the HOLD mode,
press the "DEC/HOLD" switch.
*When setting is complete, the LED goes off.
Servo speed setting
7KH GHOD\ RI HDFK VHUYR FDQ EH VHW 7KH GHOD\ FDQ EH VHW
ZLWKLQWKH QRGHOD\ WR PD[LPXPGHOD\ UDQJH
1 Set the rotary switch to the "FS/SPEED" position.
2 Push the "INC/FS" (or "DEC/HOLD") push switch to
slowly blink the LED.
*Each time the switch is pressed, the LED toggles
between off and slow blink.
3 Set the rotary switch to the channel # whose delay
you want to set.
When you want to increase the delay, push the "INC/FS"
push switch.
When you want to decrease the delay, push the "DEC/
HOLD" push switch.
*When the delay is zero, the LED goes off, when the
delay is 4 or less, the LED blinks intermittently, and when
the delay is 5 or greater, the LED blinks intermittently
twice. The delay step is 10 steps. When maximum delay
is set, the LED lights steadily.
Rotary switch
Ɣ) 6  6 3 ( ( '  )  6 V H W W L Q J  V H U Y R
o p e r a t i o n s p e e d s e t t i n g m o d e
VZLWFKLQJ
Ɣa 6HWWLQJFKDQQHOVZLWFKLQJ
Ɣ*  3&0*3&0330
PRGHVZLWFKLQJ
INC/FS push switch
Ɣ63(('VHWWLQJ 'HOD\LVLQFUHDVHGE\
pushing
Ɣ)6 VHWWLQJ  )6 PRGH LV VHW E\
pushing
DEC/HOLD push switch
Ɣ63(('VHWWLQJ 'HOD\LVGHFUHDVHGE\
pushing
Ɣ)6 VHWWLQJ  +2/' PRGH LV VHW E\
pushing
Operation monitor indicator LED (MONITOR)
Rotary switch position
Monitor LED state
Off On Slow blink
Intermittent
blink
Intermittent
double blink
Single blink
FS/SPEED
FS/HOLD
mode
SPEED
setting
mode
At switching
of rotary
switch
1-8
(In FS/HOLD setting mode)
HOLD F/S
1-8
(In SPEED setting mode)
SPEED
setting
minimum
SPPED
setting
maximum
SPEED
setting
4 or less
SPEED
setting
5 or greater
G3/1024
PCMG3
mode
PPM
mode
PCM1024
mode
Fast blink: At FS operation, receive data error, or backup error
- 3 -