Interlogix Simon XT REV B Installation Manual - Manual (Page 2)

1RWH  The total current available from the HW1&2 DC out terminal
is 250 mA at up to 120ºF (49ºC). A 24-hour battery standby for UL
requirements will be met with a maximum load of 250 mA.
With Hardwired Siren Supervision turned on, sirens connected to
HW1 I/O are supervised and require a 4.7-kohm resistor in the
circuit. If this terminal is not used, turn Hardwired Siren
Supervision off.
([WHULRUVLUHQV
For an exterior siren, reprogram HW1 to Option 6. See wiring
diagram.
1RWH  Not investigated for and may not be used in a UL Listed
installation.
+DUGZLUHGFRQWDFWV
You can connect hardwired reed switches (normally closed loop
only) to HW1 I/O (if not being used for a hardwired siren) an/or
HW2 in (terminal 3).
Connect only normally closed (NC) reed switches to HW1 I/O
and/or HW2 in. Other types of hardwired detectors should not be
used.
The total resistance of the wired loop must not exceed 3 ohms.
This allows you to use up to 200 ft. (61 m) of two-conductor, 22-
gauge stranded wire.
Connect hardwired reed switches to the panel using a 47-kohm
resistor (not a 4.7-kohm resistor) as shown in Figure 2 below.
The resistor must be connected at the last switch in the circuit.
)LJXUH 1RUPDOO\FORVHGKDUGZLUHGUHHGVZLWFKHV
H
W
1 I/O
47 kohm resistors
HW
1
&
2
D
C
out
HW2
in
9V
A
C
i
n
9V
A
C
i
n
B
a
tter
y
+
B
a
tter
y
-
1RWH  Do not install the resistor at the panel terminals. This
does not provide supervision of the wire.
:LULQJSKRQHOLQHV
You can connect a phone line to the panel for systems monitored
by a central monitoring station or systems that notify users by a
voice event notification.
DSL (digital subscriber line) allows the use of multiple devices on a
single phone line simultaneously. For DSL environments, connect
the panel line-in jack to an available phone jack on the premises.
You might also need an inline filter to ensure panel reporting is
successful.
1RWH Avoid connecting the panel to a standard phone (voice) line
in this manner. Other devices in use at the same time the panel is
using the line can prevent reports from going through.
)XOOOLQHVHL]XUH
Full line seizure allows the panel to take over (seize) the phone line,
even if another device on the line is in use. This method requires
that the panel be wired before all other phones, answering
machines, computers, or other devices on the phone line. You may
need to verify the line seizure for UL installations.
Use the RJ31X (CA-38A) jack when wiring for full line seizure. You
can then quickly and easily disconnect the panel from the phone
line in case the panel disables the phone line due to a malfunction.
7RZLUHIXOOOLQHVHL]XUHZLWKDQ5-; 
1. Run a four-conductor cable from the premises Telco block to
the RJ31X.
2. Connect the four-conductor cable wire to the RJ31X.
3. Disconnect the green and red premises phone jack wires
from the Telco block and splice them to the four-conductor
cable black and white (or yellow) wires. Use weatherproof
wire connectors for these splices.
4. Connect the four-conductor cable green and red wires to the
Telco block TIP (+) and red to RING (-) posts.
5. Connect the phone cord included with the panel to the RJ31X
and the panel LINE jack.
)XOOOLQHVHL]XUHZLULQJZLWKRQHSUHPLVHVSKRQH
If a single phone is all that exists on the premises, full line seizure
can be accomplished without an RJ31X.
1. Disconnect the phone from the premises phone jack and plug
it into the panel PHONE jack. This jack is disconnected
automatically whenever the panel reports.
2. Connect the included phone cord to the panel LINE jack and
the premises phone jack.
If a customer adds phones or other phone devices to another
phone jack, full line seizure no longer exists. Inform them to
contact you if they want to add a phone or other device so that
you can rewire for full line seizure by adding an RJ31X.
2 / 8 P/N 466-2398 • REV B • ISS 09JAN13