Interlogix Simon XT REV B Installation Manual - Manual (Page 5)

'HYLFH 7R SURJUDP
Freeze and water
sensor
Trip the tamper or press and hold the button on the
top of the sensor (cover removed) until the control
panel confirms programming. If you do not hold the
button down long enough, the system will report the
sensor as open.
Personal help
button
Press the help button until the light blinks.
Remote
touchpad
Press the emergency buttons.
Key fob Press the lock and unlock buttons at the same time.
ELM key fob Do the following:
1. Press the unlock button twice and hold it the third
time. The light button flashes three times.
2. Press the unlock button once and hold it the second
time. The light button flashes twice.
3. Press and hold the unlock button. The light button
flashes once. Hold the button until the flashing stops.
When learning (programming) sensors, the panel uses an
ascending sequence starting with 1. You can override this by
entering the desired sensor number using the number keys.
7ROHDUQ SURJUDP DVHQVRU 
1. Scroll until the display shows System Programming, and
then press OK. The display prompts for an access code.
2. Enter the dealer or installer code and press OK. The display
shows Access Codes.
3. Scroll until the display shows Sensors, and then press OK.
The display shows Learn Sensor.
4. Press OK. The display shows Trip Sensor ##, with the
number signs flashing.
If you wish to use a sensor number other than the next one
available, use the number keys to enter a two-digit sensor
number immediately.
5. Press the sensor program button or release the sensor
tamper switch. The display shows SN ## Grp10 <Front
Door>
, with Grp 10 flashing.
6. Use the number or scroll buttons if you want to enter a new
group number; press OK to accept the group number
displayed. The sensor text flashes.
7. Scroll through the text list. Press OK to accept the first text
segment.
8. You may enter more text or press OK again to finish adding
the sensor. The display shows Trip Sensor ## (with the
next available sensor number).
9. Press Status repeatedly to exit.
6HQVRUWHVWLQJ
Test the sensors after all programming is completed and
whenever a sensor-related problem occurs.
1RWH  While the sensor test is a valuable installation and service
tool, it only tests sensor operation for the current conditions. You
should perform a sensor test after any change in environment,
equipment, or programming.
Notify the central station you will be performing a test prior to
starting the test.
7RWHVWWKHVHQVRUV 
1. Place all sensors in their secured (non alarm) state.
2. Scroll to Sensor Test options under the System Tests menu,
and then press OK.
The panel will prompt you to trip each sensor one at a time.
You may follow the panel prompting or test the sensors in
any order. See Table 7 below for specific instructions on how
to trip each sensor type.
Interior sirens sound transmission beeps, and the display
identifies the tripped sensor and the number of RF packets
received. The system will continue to prompt for sensors that
have not yet been tested. When all sensors have been tested,
the display shows SN Test Complete Press Status.
3. Press Status. The display shows Sensor Test OK.
If you press Status and the panel has not heard from all
sensors, the display shows SN Test Fail or Aborted.
7DEOH 6HQVRUWULSSLQJLQVWUXFWLRQV
6HQVRU 'R
WKLV
Door/window Open the secured door or window.
Freeze Remove the sensor cover. Apply ice in a plastic bag
to the sensor (for 10 to 15 minutes). Do not allow the
sensor to get wet.
Water Press a wet rag or wet finger over both of the round,
gold-plated terminals on the underside of the sensor.
Carbon
monoxide alarm
Press and hold the Test/Hush button (approximately 5
seconds) until the unit beeps two times, and then
release the button.
Glassbreak Test with an appropriate glass break sensor tester.
Motion sensor Avoid the motion sensor field of view for 5 minutes,
and then enter its view.
Rate-of-rise heat
detector
Rub your hand together until warm, and then place
one hand on the detector for 30 seconds.
Shock Tap the glass twice, away from the sensor. Wait at
least 10 seconds before testing again.
Smoke Press and hold the test button until the system sounds
transmission beeps.
Personal help
button
Press and hold the appropriate help button until the
light blinks and the panel sounds for at least seven
beeps.
Key fob Press and hold the Lock and Unlock buttons
simultaneously for 3 seconds.
Remote
touchpad
Press and hold the two Emergency buttons
simultaneously for 3 seconds.
P/N 466-2398 • REV B • ISS 09JAN13 5 / 8