Slant/Fin EC-10 Installation User Manual
Page 2
EUTECTIC EC-10
2
Maximum operating pressure 60 psi.
All boilers hydrostatically tested — A.S.M.E.
* For forced hot water heating systems where the boiler and all piping are
located within the area to be heated, the boiler may be selected on the basis
of D.O.E. capacity output. The net AHRI output ratings shown are based on
an allowance for piping and pickup of 1.15 (water). D.O.E. capacity output is
divided by the allowance to obtain net rating. The Slant/Fin Technical Service
department should be consulted before selecting a boiler for unusual piping
and pickup requirements such as intermittent system operation, extensive
piping, etc.
† Ratings apply to the use of light oil at 140,000 Btu per gallon and apply only
when burner models listed on pages 13 and 17 of this manual are used, and
are properly adjusted to produce 13% CO2.
§ Boiler models have two firing rates. The boiler is factory shipped at the lower
firing rate. To obtain the higher firing rate, refer to the boiler installation
instructions for the appropriate field adjustments.
# All dimensions subject to normal manufacturing tolerance.
NOTE: All boilers under 300,000 Btuh (87.9 kw) input are tested and rated for
capacity under the U.S. Department of Energy (D.O.E.) Test Procedures for
Boilers.
TABLE 1: Ratings and Dimensions
EC-13P
0.65
91,000
79
69
6 x 15
87
36
22-1/4
27
5
11-13/16
2
EC-13-0.7
0.70
98,000
85
74
6 x 15
86
36
22-1/4
27
5
11-13/16
2
EC-14P
0.80
112,000
98
85
6 x 15
87
41
27-1/4
32
5
16-13/16
2
EC-14-0.9
0.90
126,000
109
95
6 x 15
86
41
27-1/4
32
5
16-13/16
2
EC-15P
1.00
140,000
123
107
6 x 15
87
46
32-1/4
37
5
21-13/16
2
EC-15-1.1
1.10
154,000
134
117
6 x 15
86
46
32-1/4
37
5
21-13/16
2
EC-16P
1.15
161,000
141
123
6 x 15
87
51
37-1/4
42
6
26-13/16
4
EC-16-1.25
1.25
175,000
152
132
6 x 15
86
51
37-1/4
42
6
26-13/16
4
BOILER
MODEL
NO.
GPH
BTUH
AHRI
BURNER
CAPACITY
OIL INPUT † §
D.O.E.
HEATING
CAPACITY
MBH *
WATER
APPROX.
OVERALL
LENGTH
“A”
AHRI
WATER
NET
RATING
MBH *
AHRI
CHIMNEY SIZE
DIMENSIONS (inches) #
I.D. ROUND
X HEIGHT
(in x ft)
AFUE %
BOILER
LENGTH
“B”
BOILER
LENGTH
“C”
FLUE
DIA.
“D”
DISTANCE
BETWEEN
LEGS
“E”
FLUE
OUTLET
LENGTH
“F”
Figure 1: Dimensions
1-1/4 threaded
supply
Flue outlet øD
1-1/4 threaded
return pipe
Drain outlet
Relief valve 3/4’’
Supply Pipe Mounted
Tridicator
Panel Mounted
Tridicator Pressure
Sensor Well
Panel Mounted
Tridicator Temperature
Sensor Well
A