Ladder seams, Costuras en escalera – SINGER 7011 User Manual
Page 50
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
Lower the presser foot and begin sewing
making certain the straight stitches fall on
the edge of the hem and the zig-zag
stitches just pierce the soft fold of the work.
Adjust stitch width if necessary. While
stitching, guide the hem edge in a straight
line and feed the soft fold evenly against
the wail of the guide.
If layers of fabric are pinned together,
remove pins as you come to them. Do not
sew over pins.
Ladder seams
A ladder seam made with blindstitching is
functional and decorative at the same time.
Appropriate for stretch and knitted fabrics,
it provides stretchable, decoratively con
structed seams and edge finishes for collars,
pockets and necklines in sportwear and
swimwear.
Recommended settings
Stitch Selection:
Blind stitch
Needle Position:
Í
0-1
Stitch Width:
1
—“WWWWlft^^
1 1
Stitch Length:
1-1/2 to 2-1/2
Foot:
General Purpose (B)
Needle Plate:
General Purpose (A)
• Make a test sample to adjust thread ten si on
and stitch length to suit your fabric. Needle
thread tension should be lighter than
normal.
• Cut and fit garment, allfow % inch (16mm)
seam allowance. Baste seam line.
• Position fabric so that the large zig-zag
stitches fall on the stitching line, towards
the centre of the garment
•
• When stitching is completed, open the
seam by pulling the fabric back on opposite
sides of seam to produce a ladder effect
and press seam allowances.
Baje el prénsatelas y empiece a coser
asegurándose que los puntos rectos caigan
sobre el borde del dobladillo y los puntos en
zig-zag justo sobre el doblez blando de la
labor. Ajuste el ancho del punto si fuese
necesario. Mientras cose guíe el borde del
dobladillo en línea recta y arrastre con
suavidad el doblez blando contra la pared de
la guía.
Si ios pliegues del tejido están sujetos con
alfileres, quítelos según se aproxima a ellos.
No cosa sobre los alfileres.
Costuras en escalera
Posiciones recomendadas
Selección punto: Puntada Invisible
Posición aguja:
Anchura punto: ]---vvW\/\/\/\/yyyy^
Longitud punto: 1 -1 /2 a 2-1 /2
Prénsatelas: Uso general (B)
Plancha aguja: Uso general (A)
Una costura en escalera realizada con la
Puntada Invisible es funcional y decorativa al
mismo tiempo. Apropiada para tejidos elásticos
y de punto, ya que aporta elasticidad, costuras
decoradamente formadas y acabado de bordes
para cuellos, bolsillos y bandas en prendas
deportivas y bañadores.
• Haga una muestra para ajustar la tensión del
hilo y la longitud del punto apropiada para su
tejido. La tensión dél hilo de la aguja debería
ser más ligera que la normal.
• Corte y ajuste la prenda, dejando 16 mm. de
tolerancia de costura. Hilvane la línea a
coser.
• Coloque el tejido de manera que el vértice de
los puntos zig-zag caigan sobre la línea de
costura, hacia el centro del tejido.
• Cuando se ha completado la costura, abrirla,
tirando del tejido hacia atrás por los lados
opuestos a la costura, lo que producirá un
efecto de escalera. Planche.
48