Document Outline

• Contents
• 1 Safety
  • 1.1 Action-related warnings
  • 1.2 Required personnel qualifications
  • 1.3 General safety information
    • 1.3.1 Danger caused by improper operation
    • 1.3.2 Risk of death from electric shock
    • 1.3.3 Risk of death due to lack of safety devices
    • 1.3.4 Risk of being scalded by hot drinking water
    • 1.3.5 Risk of injury or material damage due to incorrect handling of the product
    • 1.3.6 Risk of material damage due to additional elements in the heating water
    • 1.3.7 Risk of material damage caused by using an unsuitable tool
    • 1.3.8 Avoid environmental damage caused by escaping coolant
  • 1.4 Regulations (directives, laws, standards)
  • 1.5 CE label
  • 1.6 Approvals
  • 1.7 Local regulations
  • 1.8 Regulations
    • 1.8.1 Statutory requirements
    • 1.8.2 Standards
    • 1.8.3 Reminder of existing regulatory acts
  • 1.9 Other regulations
    • 1.9.1 Control of Substances Hazardous to Health
  • 1.10 Intended use
• 2 Notes on the documentation
  • 2.1 Observing other applicable documents
  • 2.2 Storing documents
  • 2.3 Applicability of the instructions
• 3 System overview
  • 3.1 Safety devices
  • 3.2 Functionality
    • 3.2.1 Heating mode
    • 3.2.2 Thawing
    • 3.2.3 Application limits
      • 3.2.3.1 Application limits in heating mode (Envirosorb3 5)
      • 3.2.3.2 Application limits in heating mode (Envirosorb3 8, Envirosorb3 11, Envirosorb3 15)
  • 3.3 Permitted hydraulic configurations
    • 3.3.1 Direct connection to a heating installation
    • 3.3.2 Indirect connection to a heating installation via a hydraulic module
  • 3.4 System diagram (Envirosorb3 5)
  • 3.5 System diagram (Envirosorb3 8, Envirosorb3 11, Envirosorb3 15)
• 4 Overview of the equipment
  • 4.1 Type designation and serial number
  • 4.2 Information on the identification plate
• 5 Assembly and installation
  • 5.1 Preparing for fitting and installation
    • 5.1.1 Delivery, transport and positioning
      • 5.1.1.1 Transporting the product
      • 5.1.1.2 Unpacking the product
      • 5.1.1.3 Checking the scope of delivery
    • 5.1.2 Complying with clearances and installation clearances
      • 5.1.2.1 Unit dimensions and connection dimensions
      • 5.1.2.2 Installation clearance
      • 5.1.2.3 Selecting the installation site
      • 5.1.2.4 Installing the heat pump
      • 5.1.2.5 Preparing the condensate discharge
  • 5.2 Carrying out the installation
    • 5.2.1 Removing the side casing
    • 5.2.2 Aligning the product
  • 5.3 Hydraulics installation
    • 5.3.1 Carrying out the hydraulics installation
    • 5.3.2 Connecting the swimming pool (optional)
    • 5.3.3 Connecting the condensate drain pipework
  • 5.4 Carrying out the electrical installation
    • 5.4.1 Establishing the power supply
    • 5.4.2 Standard tariff
      • 5.4.2.1 230 V connection
    • 5.4.3 Laying the 24 V cabling
    • 5.4.4 Installing the cable duct
  • 5.5 Connection diagrams
    • 5.5.1 Connection diagram
• 6 Start-up
  • 6.1 Run the start-up
  • 6.2 Filling the heating circuit
  • 6.3 Treating the heating water
  • 6.4 Filling the heating installation
  • 6.5 Activating the heat pump
  • 6.6 Checking the product's operation
  • 6.7 Operating noises
  • 6.8 Adjusting the heating circuit
    • 6.8.1 Purging the heating circuit
      • 6.8.1.1 Available pressure in the heat pump heating circuit
    • 6.8.2 Adjusting the heating circuit flow rate
  • 6.9 Installing the side cladding
  • 6.10 Instructing the operator
• 7 Maintenance
  • 7.1 Observing maintenance intervals
  • 7.2 Preparing for maintenance
    • 7.2.1 Procuring spare parts
  • 7.3 Instructions before carrying out maintenance work
  • 7.4 Yearly maintenance
  • 7.5 Cleaning the product
    • 7.5.1 Cleaning the front
    • 7.5.2 Cleaning the back
  • 7.6 Draining the product
  • 7.7 Checking the product's status codes
  • 7.8 Checking the electrical installation
  • 7.9 Start-up following maintenance
• 8 Troubleshooting
  • 8.1 Troubleshooting
  • 8.2 Fault codes
• 9 Decommissioning
  • 9.1 Temporary decommissioning
  • 9.2 Permanently decommissioning
• 10 Customer service
• 11 Disposal
  • 11.1 Recycling and disposal
  • 11.2 Arranging disposal of coolant
• Appendix
  • A Heat pump schematic
    • A.1 Heat pump schematic drawing (Envirosorb3 5)
    • A.2 Heat pump schematic drawing (Envirosorb3 8)
    • A.3 Heat pump schematic drawing (Envirosorb3 11)
    • A.4 Heat pump schematic drawing (Envirosorb3 15)
  • B Heat pump setting parameters
  • C Technical data
  • D Status codes
  • E Overview of fault codes
• Index
  • B
  • C
  • D
  • E
  • F
  • H
  • I
  • M
  • P
  • R
  • S
  • T
  • V