Document Outline

• mn-cdm625_15.pdf
  • INSIDE COVER
  • TABLE OF CONTENTS
  • INDEX OF TABLES
  • IND EX OF FIGURES
  • PREFACE
    • About this Manual
    • Conventions and References
      • Patents and Trademarks
      • Warnings, Cautions, and Notes
      • Recommended Standard Designations
    • Safety and Compliance
      • Electrical Safety and Compliance
      • Grounding
      • Electrical Installation
      • Battery
      • Fuses
      • Operating Environment
      • European Union Radio Equipment and Telecommunications Terminal Equipment (R&TTE) Directive (1999/5/EC) and EN 301 489-1
        • European Union Electromagnetic Compatibility (EMC) Directive (2004/108/EC)
        • European Union Low Voltage Directive (LVD) (2006/95/EC)
        • European Union RoHS Directive (2002/95/EC)
        • European Union Telecommunications Terminal Equipment Directive (91/263/EEC)
        • CE Mark
    • Product Support
    • Comtech EF Data Headquarters
    • Warranty Policy
      • Limitations of Warranty
      • Exclusive Remedies
  • Chapter 1. INTRODUCTION
    • 1.1 Overview
    • 1.2 Functional Description
    • 1.3 Features
      • 1.3.1 Physical Description
      • 1.3.2 Modem Compatibility
      • 1.3.3 Verification
      • 1.3.4 Updating Modem Firmware
      • 1.3.5 Standard Data Interfaces
      • 1.3.6 Optional Hardware and Accessories
      • 1.3.7 Fully Accessible System Topology (FAST)
      • 1.3.8 Supporting Hardware and Software
      • 1.3.9 Physical Features
        • 1.3.9.1 Dimensional Envelope
        • 1.3.9.2 Front Panel
        • 1.3.9.3 Rear Panel
    • 1.4 Summary of Specifications
      • 1.4.1 Modulator
      • 1.4.2 Demodulator
      • 1.4.3 Data Interfaces
      • 1.4.4 Automatic Uplink Power Control (AUPC)
      • 1.4.5 DoubleTalk® Carrier- in-Carrier® (CnC)
      • 1.4.6 Framing Summary
      • 1.4.7 Data Rate Ranges
      • 1.4.8 VersaFEC Adaptive Coding and Modulation (ACM)
      • 1.4.9 Miscellaneous
      • 1.4.10 Approvals
  • Chapter 2. INSTALLATION
    • 2.1 Unpack and Inspect the Shipment
    • 2.2 Install the Unit Into a Rack Enclosure
      • 2.2.1 Install the Optional Rear-Mounting Support Brackets Kits
    • 2.3 Configure the CDM-625
    • 2.4 Verify Modem Operation
    • 2.5 Connect the External Cables
  • Chapter 3. REAR PANEL CONNECTORS and PINOUTS
    • 3.1 CDM-625 Rear Panel Overview
    • 3.2 CDM-625 Cable Connections
      • 3.2.1 IF Connection Group
        • 3.2.1.1 Rx IF Connectors
        • 3.2.1.2 Tx IF Connectors
      • 3.2.2 Terrestrial Data Connection Group
        • 3.2.2.1 Data Interface (DB-25F)
          • 3.2.2.1.1 HSSI Operation via the CIC-60 Interface Adapter Module
        • 3.2.2.2 G.703 Connectors
          • 3.2.2.2.1 Balanced G.703 (DB-9F)
          • 3.2.2.2.2 Aux G.703 (DB-9F)
          • 3.2.2.2.3 Quad E1 Operation via the Balanced G.703 / Aux G.703 Connectors
            • 3.2.2.2.3.1 CA-0000163 Adapter Cable
            • 3.2.2.2.3.2 /CA-0000164 Adapter Cable
            • 3.2.2.2.3.3 KT-0000122/KT-0020570 Quad E1 Balanced/Unbalanced Adapter /Cable Kits
          • 3.2.2.2.4 Unbal G.703 / ASI – Out (IDO), In (DDI)
          • 3.2.2.2.5 G.703 IDI (Insert Data In), DDO (Drop Data Out)
        • 3.2.2.3 Quad 10/100 Ethernet (RJ-45)
        • 3.2.2.4 IDR Data / Alarms / Audio (HD-44F)
        • 3.2.2.5 ESC (DB-9F)
      • 3.2.3 Utility Connections Group
        • 3.2.3.1 Remote Control (DB-9M)
        • 3.2.3.2 Alarms (DB-15M)
        • 3.2.3.3 PMSI Connector, DB-9F
        • 3.2.3.4 1:1 Control (DB-9F)
        • 3.2.3.5 /Ext Ref In/Out
    • 3.3 CDM-625 Ground and Power Connections
      • 3.3.1 Chassis Ground Interface
      • 3.3.2 Standard 100V/240V Alternating Current (AC) Power Interface
        • 3.3.2.1 AC Operation – CDM-625 Accessories
        • 3.3.2.2 AC Operation – Apply Power
        • 3.3.2.3 AC Operation – Replace the Fuses
      • 3.3.3 Optional 48V Direct Current (DC) Power Interface
        • 3.3.3.1 Optional DC Operation – CDM-625 Accessories
        • 3.3.3.2 Optional DC Operation – Apply Power
        • 3.3.3.3 Optional DC Operation – Replace the Fuses
  • Chapter 4. UPDATING FIRMWARE
    • 4.1 Updating Firmware via Internet
    • 4.2 About Firmware Files, Naming, Versions, and Archive Formats
    • 4.3 Firmware Update Procedure
      • 4.3.1 Getting Started: Preparing for the Firmware Download
      • 4.3.2 Downloading and Extracting the Firmware Update
      • 4.3.3 Executing the Ethernet FTP Upload Procedure
  • Chapter 5. FRONT PANEL OPERATION
    • 5.1 Overview
      • 5.1.1 LED Indicators
      • 5.1.2 Keypad
      • 5.1.3 Vacuum Fluorescent Display (VFD)
        • 5.1.3.1 Screen Saver
        • 5.1.3.2 Opening Screen
          • 5.1.3.2.1 Feature Availability/Operation Indicators via the Opening Screen
    • 5.2 SELECT: (Main) Menu
      • 5.2.1 SELECT: Configuration Menus
        • 5.2.1.1 CONFIG: All
        • 5.2.1.2 CONFIG: Mode
        • 5.2.1.3 CONFIG: Tx
          • 5.2.1.3.1 CONFIG: Tx ( Tx-IF
          • 5.2.1.3.2 CONFIG: Tx ( Freq (Frequency)
          • 5.2.1.3.3 CONFIG: Tx ( Power
            • 5.2.1.3.3.1 CONFIG: Tx ( Power ( Mode ( AUPC
          • 5.2.1.3.4 CONFIG: Tx ( FEC
          • 5.2.1.3.5 CONFIG: Tx ( Mod (Modulation)
          • 5.2.1.3.6 CONFIG: Tx ( Data
          • 5.2.1.3.7 CONFIG: Tx ( Symb (IP-ACM Mode Only)
          • 5.2.1.3.8 CONFIG: Tx ( Scrambler
        • 5.2.1.4 CONFIG: Rx
          • 5.2.1.4.1 CONFIG: Rx ( Rx-IF
          • 5.2.1.4.2 CONFIG: Rx (Freq (Frequency)
          • 5.2.1.4.3 CONFIG: Rx ( FEC
          • 5.2.1.4.4 CONFIG: Rx ( Demod (Demodulation)
          • 5.2.1.4.5 CONFIG: Rx ( Data
          • 5.2.1.4.6 CONFIG: Rx ( Symb (IP-ACM Mode Only)
          • 5.2.1.4.7 CONFIG: Rx ( Descram (Descrambler)
          • 5.2.1.4.8 CONFIG: Rx ( Eq (Equalizer)
          • 5.2.1.4.9 CONFIG: Rx ( EbNo
        • 5.2.1.5 CONFIG: Clocks
          • 5.2.1.5.1 CONFIG: Clocks ( Tx Clock
          • 5.2.1.5.2 CONFIG: Clocks ( Rx Buffer/Clock
          • 5.2.1.5.3 CONFIG: Clocks ( Clk-Ext (G.703 Clock Extension)
          • 5.2.1.5.4 CONFIG: Clocks ( Freq-Ref
          • 5.2.1.5.5 CONFIG: Clocks ( Int-Ref-Adjust
        • 5.2.1.6 CONFIG: D&I (Drop & Insert)
          • 5.2.1.6.1 CONFIG: D&I ( Loop
          • 5.2.1.6.2 CONFIG: D&I ( Drp-Type or Ins-Type
          • 5.2.1.6.3 CONFIG: D&I ( (Drop or Insert) Chan/TS (Channel Timeslots)
          • 5.2.1.6.4 CONFIG: Quad D&I (QDI)
        • 5.2.1.7 CONFIG: ACM (Adaptive Coding and Modulation) (IP-ACM Mode Only)
          • 5.2.1.7.1 CONFIG: ACM ( Min/Max-ModCod
          • 5.2.1.7.2 CONFIG: ACM ( Unlock-Action
          • 5.2.1.7.3 CONFIG: ACM ( Target-EbNo-Margin
        • 5.2.1.8 CONFIG: CnC
          • 5.2.1.8.1 CONFIG: CnC ( Mode
          • 5.2.1.8.2 CONFIG: CnC ( CONFIG: CnC ( Freq-Offset
          • 5.2.1.8.3 CONFIG: CnC ( Search-Delay
          • 5.2.1.8.4 CONFIG: CnC ( PMSI-Control
        • 5.2.1.9 CONFIG: EDMAC
        • 5.2.1.10 CONFIG: Misc
          • 5.2.1.10.1 CONFIG: Misc ( G.703-LineCode (Ternary Code)
          • 5.2.1.10.2 CONFIG: Misc ( IDR-ESC
          • 5.2.1.10.3 CONFIG: Misc ( HSSI
          • 5.2.1.10.4 CONFIG: Misc ( RTS
          • 5.2.1.10.5 CONFIG: Misc ( Audio-Vol (ADPCM Audio Volumes)
          • 5.2.1.10.6 CONFIG: Misc ( HiRateESC
          • 5.2.1.10.7 CONFIG: Misc ( Warm-Up
          • 5.2.1.10.8 CONFIG: Misc ( Stats (Statistics)
          • 5.2.1.10.9 CONFIG: Misc ( MEO
            • 5.2.1.10.9.1 CONFIG: Misc ( MEO (Antenna Handover
        • 5.2.1.11 CONFIG: Mask
          • 5.2.1.11.1 CONFIG: Mask ( AIS
          • 5.2.1.11.2 CONFIG: Mask ( Buffer or Ref
          • 5.2.1.11.3 CONFIG: Mask ( RxIF
          • 5.2.1.11.4 CONFIG: Mask ( TxClk
          • 5.2.1.11.5 CONFIG: Mask ( TxSat (Satellite Tx Alarms)
          • 5.2.1.11.6 CONFIG: Mask ( RxSat (Satellite Rx Alarms)
          • 5.2.1.11.7 CONFIG: Mask ( Terr
          • 5.2.1.11.8 CONFIG: Mask ( ROp (RAN Optimization) (FUTURE)
          • 5.2.1.11.9 CONFIG: Mask ( BUC
          • 5.2.1.11.10 CONFIG: Mask ( LNB
          • 5.2.1.11.11 CONFIG: Mask ( CEX (G.703 Clock Extension mask)
        • 5.2.1.12 CONFIG: Remote (Remote Control)
          • 5.2.1.12.1 CONFIG: Remote ( Local or Serial remote settings
        • 5.2.1.13 CONFIG: IP
          • 5.2.1.13.1 CONFIG: IP ( Addresses
          • 5.2.1.13.2 CONFIG: IP ( SNMP
          • 5.2.1.13.3 CONFIG: IP ( Setup
          • 5.2.1.13.4 CONFIG: IP ( ANT (Advanced Network Timing)
            • 5.2.1.13.4.1 CONFIG: IP ( ANT ( SNTP (Simple Network Time Protocol)
            • 5.2.1.13.4.2 CONFIG: IP ( ANT ( PTP (Precision Time Protocol)
          • 5.2.1.13.5 CONFIG: IP (AccessList
          • 5.2.1.13.6 CONFIG: IP ( PktP-Enable
      • 5.2.2 SELECT: Test Menus
        • 5.2.2.1 SELECT: TEST ( Mode
        • 5.2.2.2 SELECT: TEST ( BERT
          • 5.2.2.2.1 SELECT: TEST ( BERT ( Config
          • 5.2.2.2.2 SELECT: TEST ( BERT ( Monitor
        • 5.2.2.3 SELECT: TEST ( CnC-APC-Monitor
        • 5.2.2.4 SELECT: TEST ( Uncorrected-BER
      • 5.2.3 SELECT: Monitor Menus
        • 5.2.3.1 Monitor: Live-Alarms
        • 5.2.3.2 Monitor: Stored Events
        • 5.2.3.3 Monitor: ACM
        • 5.2.3.4 Monitor: Statistics
        • 5.2.3.5 Monitor: Rx Parameters
        • 5.2.3.6 Monitor: AUPC-Parameters
        • 5.2.3.7 Monitor: CnC-Parameters
        • 5.2.3.8 Monitor: IP Statistics
      • 5.2.4 SELECT: Info (Information) Menus
        • 5.2.4.1 Info: All
        • 5.2.4.2 Info: ID
        • 5.2.4.3 Info: Mode
        • 5.2.4.4 Info: Tx
        • 5.2.4.5 Info: Rx
        • 5.2.4.6 Info: Clocks
        • 5.2.4.7 Info: EDMAC
        • 5.2.4.8 Info: Drop
        • 5.2.4.9 Info: Insert
        • 5.2.4.10 Info: Remote
        • 5.2.4.11 Info: Alarms Mask
        • 5.2.4.12 Info: Misc
      • 5.2.5 SELECT: Store/Ld (Store/Load) Menus
      • 5.2.6 SELECT: Utility Menus
        • 5.2.6.1 Utilities: Set-RTC
        • 5.2.6.2 Utilities: Display-Bright
        • 5.2.6.3 Utilities: CarrID
        • 5.2.6.4 Utilities: LED
        • 5.2.6.5 Utilities: Redundancy
          • 5.2.6.5.1 Utilities: Redundancy ( Traffic-IP-Addr/Range
          • 5.2.6.5.2 Utilities: Redundancy ( 1:1
          • 5.2.6.5.3 Utilities: Redundancy ( 1:N
        • 5.2.6.6 Utilities: Circuit-ID
        • 5.2.6.7 Utilities: Firmware
          • 5.2.6.7.1 Utilities: Firmware ( Base-Modem
            • 5.2.6.7.1.1 Utilities: Firmware ( Base-Modem ( Boot-ROM, Image#X
            • 5.2.6.7.1.2 Utilities: Firmware ( Base-Modem (Select
          • 5.2.6.7.2 Utilities: Firmware ( Packet-Processor
            • 5.2.6.7.2.1 Utilities: Firmware ( Packet-Processor ( Boot-ROM, Image#X
            • 5.2.6.7.2.2 Utilities: Firmware ( Packet-Processor (Select
        • 5.2.6.8 Utilities: Em (CDM-600/600L Emulation)
      • 5.2.7 SELECT: ODU Menus (Summary Only)
      • 5.2.8 SELECT: FAST Menus
        • 5.2.8.1 FAST: Options
          • 5.2.8.1.1 FAST: Options ( View Options
          • 5.2.8.1.2 FAST: Options ( Set Registers
        • 5.2.8.2 FAST: Demo-Mode
        • 5.2.8.3 FAST: CnC
  • Chapter 6. ETHERNET-BASED REMOTE PRODUCT MANAGEMENT
    • 6.1 Overview
    • 6.2 Ethernet Management Interface Connectors
    • 6.3 SNMP Interface
      • 6.3.1 Management Information Base (MIB) Files
      • 6.3.2 SNMP Community Strings
      • 6.3.3 SNMP Traps
    • 6.4 Telnet Interface
      • 6.4.1 Using the Telnet Interface for Remote Control Operation
        • 6.4.1.1 Using HyperTerminal for Telnet Remote Control Operation
      • 6.4.2 Using the Telnet Interface for Telnet Command Line Interface (CLI) Operation
    • 6.5 Web Server (HTTP) Interface
      • 6.5.1 User Login
      • 6.5.2 Web Server Interface – Operational Features
        • 6.5.2.1 Navigation
        • 6.5.2.2 /Page Sections
        • 6.5.2.3 Action Buttons
        • 6.5.2.4 Drop-down Lists
        • 6.5.2.5 Text or Data Entry
      • 6.5.3 Web Server Interface – Menu Tree
        • 6.5.3.1 Conditional Access to IP Packet Processor Pages
      • 6.5.4 Web Server Page Descriptions
        • 6.5.4.1 Home Pages
          • 6.5.4.1.1 Home | Home
          • 6.5.4.1.2 Home | Contact
          • 6.5.4.1.3 Home | Support
        • 6.5.4.2 Admin Pages
          • 6.5.4.2.1 Admin | Access
          • 6.5.4.2.2 Admin | SNMP
          • 6.5.4.2.3 Admin | Firmware Pages
            • 6.5.4.2.3.1 Admin | Firmware | Base Modem
            • 6.5.4.2.3.2 Admin | Firmware | Packet Processor
          • 6.5.4.2.4 Admin | Reboot
          • 6.5.4.2.5 Admin | FAST
          • 6.5.4.2.6 Admin | Utilities
        • 6.5.4.3 Configuration Pages
          • 6.5.4.3.1 Configuration | Modem
          • 6.5.4.3.2 Configuration | LAN Pages
            • 6.5.4.3.2.1 Configuration | LAN | IP
            • 6.5.4.3.2.2 Configuration | LAN | ARP
          • 6.5.4.3.3 Configuration | Routing Pages
            • 6.5.4.3.3.1 Configuration | Routing | Routes
            • 6.5.4.3.3.2 Configuration | Routing | IGMP
            • 6.5.4.3.3.3 Configuration | Routing | DHCP
            • 6.5.4.3.3.4 Configuration | Routing | DNS
          • 6.5.4.3.4 Configuration | Managed Switch
          • 6.5.4.3.5 Configuration | WAN Pages
            • 6.5.4.3.5.1 Configuration | WAN | QoS Pages
              • 6.5.4.3.5.1.1 Configuration | WAN | QoS Pages – Max/Priority, Min/Max Modes
              • 6.5.4.3.5.1.2 Configuration | WAN | QoS Pages – DiffServ Mode
            • 6.5.4.3.5.2 Configuration | WAN | Compression
            • 6.5.4.3.5.3 Configuration | WAN | Encryption
          • 6.5.4.3.6 Configuration | Overhead
          • 6.5.4.3.7 Configuration | Utilities
          • 6.5.4.3.8 Configuration | D&I (Drop and Insert)
          • 6.5.4.3.9 Configuration | BUC (Block Up Converter)
          • 6.5.4.3.10 Configuration | LNB (Low Noise Block Down Converter)
          • 6.5.4.3.11 Configuration | ANT (Advanced Network Timing) Pages
            • 6.5.4.3.11.1 Configuration | ANT | PTP (Precision Time Protocol)
            • 6.5.4.3.11.2 Configuration | ANT | SNTP (Simple Network Timing Protocol)
          • 6.5.4.3.12 Configuration | MEO (Mid-Earth Orbit)
        • 6.5.4.4 Status Pages
          • 6.5.4.4.1 Status | Modem Status
          • 6.5.4.4.2 Status | Modem Logs
            • 6.5.4.4.2.1 Status | Modem Logs | Base Modem
            • 6.5.4.4.2.2 Status | Modem Logs | Packet Processor
          • 6.5.4.4.3 Status | Modem Info
          • 6.5.4.4.4 Status | Traffic Statistics Pages
            • 6.5.4.4.4.1 Status | Traffic Statistics | Ethernet
            • 6.5.4.4.4.2 Status | Traffic Statistics | Router
            • 6.5.4.4.4.3 Status | Traffic Statistics | Managed Switch
            • 6.5.4.4.4.4 Status | Traffic Statistics | WAN
            • 6.5.4.4.4.5 Status | Traffic Statistics | Compression
            • 6.5.4.4.4.6 Status | Traffic Statistics | QoS
            • 6.5.4.4.4.7 Status | Traffic Statistics | PTP
            • 6.5.4.4.4.8 Status | Traffic Statistics | MAC Table
            • 6.5.4.4.4.9 Status | Traffic Statistics | Clear Counters
          • 6.5.4.4.5 Status | Performance Pages
            • 6.5.4.4.5.1 Status | Performance | Performance
            • 6.5.4.4.5.2 Status | Performance | Graphs
        • 6.5.4.5 ODU (Outdoor Unit) Pages (Summary Only)
        • 6.5.4.6 Redundancy page
  • Chapter 7. FORWARD ERROR CORRECTION OPTIONS
    • 7.1 Overview
    • 7.2 Viterbi
    • 7.3 Sequential
    • 7.4 Reed-Solomon Outer Codec
      • 7.4.1 Closed Network Modes
      • 7.4.2 Open Network Modes
    • 7.5 Trellis Coding (FAST Option)
    • 7.6 Turbo Product Codec (Hardware Option)
    • 7.7 TPC and Low Density Parity Check (LDPC) coding
      • 7.7.1 About TPC/LDPC
      • 7.7.2 LDPC versus TPC
      • 7.7.3 End-to-End Processing Delay
    • 7.8 VersaFEC (Short-block LDPC)
      • 7.8.1 VersaFEC Extensions
        • 7.8.1.1 Extended CCM Codes
        • 7.8.1.2 Ultra-Low-Latency (ULL) Codes
    • 7.9 Uncoded Operation (No FEC)
  • Chapter 8. AUTOMATIC UPLINK POWER CONTROL (AUPC)
    • 8.1 Overview
    • 8.2 Setting AUPC Parameters
      • 8.2.1 Target Eb/No
      • 8.2.2 Max Range
      • 8.2.3 Alarm
      • 8.2.4 Demod Unlock
    • 8.3 Compensation Rate
    • 8.4 Monitoring
  • Chapter 9. CLOCK MODES and DROP AND INSERT (D&I)
    • 9.1 Overview
    • 9.2 Transmit Clocking
      • 9.2.1 Internal Clock
      • 9.2.2 TX Terrestrial
      • 9.2.3 RX Loop-Timed, RX=TX
      • 9.2.4 RX Loop-Timed, RX<>TX (Asymmetric Loop Timing)
      • 9.2.5 External TT with ST = RX Satellite
    • 9.3 Receive Clocking
      • 9.3.1 Buffer Disabled (RX Satellite)
      • 9.3.2 Buffer Enabled, TX=RX (TX Terrestrial or Int (SCT) Clock)
      • 9.3.3 Buffer Enabled, RX<>TX (TX Terrestrial or Int (SCT) Clock)
    • 9.4 X.21 Notes
    • 9.5 Drop and Insert
    • 9.6 Frame Formats
    • 9.7 Timeslot Selection
    • 9.8 Drop and Insert (D&I) Clocking
    • 9.9 RX Buffer Clock = Insert (D&I only)
    • 9.10 Single-Source Multiple Modems
    • 9.11 G.703 Clock Extension
      • 9.11.1 Clock Extension Mode 1
      • 9.11.2 Clock Extension Mode 2
      • 9.11.3 Clock Extension Mode 3
    • 9.12 Quad E1 Operation
  • Chapter 10. DoubleTalk Carrier-in-Carrier OPTION
    • 10.1 Overview
    • 10.2 What is DoubleTalk Carrier-in-Carrier?
    • 10.3 Application Requirements
      • 10.3.1 Operational Recommendations
    • 10.4 System Functionality and Operational Considerations
      • 10.4.1 DoubleTalk Carrier-in-Carrier Cancellation Process
      • 10.4.2 Margin Requirements
      • 10.4.3 Carrier-in-Carrier Latency
      • 10.4.4 Carrier-in-Carrier and Adaptive Coding and Modulation
      • 10.4.5 Carrier-in-Carrier Link Design
        • 10.4.5.1 Symmetric Data Rate Link
        • 10.4.5.2 Asymmetric Data Rate Link
        • 10.4.5.3 Power Limited Links
      • 10.4.6 Carrier-in-Carrier Commissioning and Deployment
      • 10.4.7 Validate Carrier-in-Carrier Performance
    • 10.5 Operational References
      • 10.5.1 Calculate Carrier-in-Carrier Link Budget
      • 10.5.2 Methods to Use to Estimate PSD Ratio
        • 10.5.2.1 Use Downlink EIRP and Symbol Rate
        • 10.5.2.2 Use LST
        • 10.5.2.3 Use SatMaster
        • 10.5.2.4 Use a Spectrum Analyzer
    • 10.6 Carrier-in-Carrier Automatic Power Control (CnC-APC)
      • 10.6.1 About CnC-APC
      • 10.6.2 AUPC and Carrier-in-Carrier in the CDM-625
      • 10.6.3 The CnC Automatic Power Control Algorithm
      • 10.6.4 CnC-APC Framing
        • 10.6.4.1 CnC-APC Framing and the Self-Locking Problem
      • 10.6.5 CnC-APC Response Time
      • 10.6.6 CnC-APC Setup
      • 10.6.7 CnC-APC Redundancy Support Notes
    • 10.7 DoubleTalk Carrier-in-Carrier Specifications
    • 10.8 Carrier-in-Carrier Summary
    • 10.9 Glossary
    • Bandwidth, Allocated or Occupied
    • Bandwidth, Leased (LBW)
    • Bandwidth, Power Equivalent (PEB)
    • CnC Ratio
    • Eb/No
    • Es/No
    • C/N
    • C/No
    • Co+No/No
    • Power Spectral Density (PSD)
    • PSD Ratio
    • Quasi Error Free (QEF)
    • Spectral Efficiency (SE)
    • Symbol Rate & Data Rate
  • Chapter 11. EDMAC CHANNEL
    • 11.1 Overview
      • 11.1.1 EDMAC
      • 11.1.2 Drop & Insert ++
      • 11.1.3 EDMAC-3
    • 11.2 EDMAC Channel M&C Connection
    • 11.3 EDMAC Channel Setup
  • Chapter 12. ESC++
    • 12.1 Overview
    • 12.2 Overhead Details
    • 12.3 Available Baud Rates
    • 12.4 Configuration
    • 12.5 Effect on Eb/No Performance
  • Chapter 13. OFFSET QPSK OPERATION
  • Chapter 14. OPEN NETWORK OPERATIONS
    • 14.1 Overview
    • 14.2 Intelsat Business Service (IBS)
      • 14.2.1 IBS Clock/Data Recovery and De-jitter
      • 14.2.2 IBS Framing
      • 14.2.3 IBS Engineering Service Channel
      • 14.2.4 IBS Scrambling
    • 14.3 Drop and Insert (D&I)
      • 14.3.1 D&I Primary Data Interfaces
      • 14.3.2 D&I Framing
    • 14.4 Intermediate Data Rate (IDR)
      • 14.4.1 IDR Primary Data Interfaces
      • 14.4.2 IDR Engineering Service Channel
  • Chapter 15. IP Sub-Mux
    • 15.1 Overview
    • 15.2 Available Ratios
    • 15.3 Data Rate vs. Composite Rate
  • Chapter 16. ETHERNET NETWORK CONFIGURATION
    • 16.1 Overview
    • 16.2 CDM-625 Ethernet Overview
      • 16.2.1 Interface Architecture
      • 16.2.2 Modes of Ethernet Operation
      • 16.2.3 Ethernet Networking Loops
        • 16.2.3.1 Networking Loops in Managed Switch Mode
          • 16.2.3.1.1 Hub-to-Hub using Ethernet Switches
          • 16.2.3.1.2 Hub-to-Hub using Ethernet Routers
          • 16.2.3.1.3 Hub-to-Remotes using Ethernet Switches or Routers
        • 16.2.3.2 Networking Loops in Router Mode (with IP Packet Processor)
    • 16.3 Ethernet Network Configurations in Managed Switch Mode
      • 16.3.1 Point-to-Multipoint Hub-to-Remotes, Split-path Traffic Using Routers
      • 16.3.2 Point-to-Multipoint Hub-to-Remotes, Split-path Traffic Using Switches
    • 16.4 Ethernet Network Configurations in Router Mode (with IP Packet Processor)
      • 16.4.1 Point-to-Multipoint (Router Multipoint Hub) Mode
        • 16.4.1.1 Router Multipoint Hub Configuration
      • 16.4.2 Multicast Routing Mode
        • 16.4.2.1 Multicast Routing Configuration
    • 16.5 Ethernet Overhead over WAN Interface
      • 16.5.1 Managed Switch Mode (without IP Packet Processor)
      • 16.5.2 Router Mode or Managed Switch Mode (with IP Packet Processor)
    • 16.6 Ethernet Redundancy
    • 16.7 Advanced Network Timing
      • 16.7.1 Overview
      • 16.7.2 SNTP (Simple Network Time Protocol)
      • 16.7.3 PTP (Precision Time Protocol)
  • Chapter 17. ADAPTIVE CODING and MODULATION (ACM)
    • 17.1 Overview
    • 17.2 Background
    • 17.3 Requirements for ACM
    • 17.4 An Existing Satellite ACM Scheme
    • 17.5 Disadvantages of DVB-S2
    • 17.6 VersaFEC ACM
    • 17.7 VersaFEC ACM Latency
    • 17.8 Configuring VersaFEC ACM in the CDM-625
    • 17.9 Monitoring ACM performance
    • 17.10 ACM Congestion Control
    • 17.11 Notes and Recommendations
    • 17.12 VersaFEC ACM – Summary of Specifications
  • Chapter 18. IP PACKET PROCESSOR OPTION
    • 18.1 Overview
      • 18.1.1 IP Packet Processor – Operational Requirements
      • 18.1.2 Interoperability Compatibility/Limitations
    • 18.2 IP Packet Processor Features
      • 18.2.1 Streamline Encapsulation (SLE)
      • 18.2.2 Modes of Operation
      • 18.2.3 Subsystem Multiplex (Sub-Mux)
      • 18.2.4 Adaptive Coding and Modulation (ACM)
      • 18.2.5 FAST Options
        • 18.2.5.1 Header Compression
        • 18.2.5.2 Payload Compression
        • 18.2.5.3 Advanced Quality of Service (QoS)
        • 18.2.5.4 Advanced Encryption Standard (AES) Encryption
    • 18.3 CDM-625 Operation with IP Packet Processor
      • 18.3.1 Front Panel Operation
      • 18.3.2 Ethernet-based Remote Product Management
        • 18.3.2.1 SNMP Interface
        • 18.3.2.2 Telnet Interface
        • 18.3.2.3 Web Server (HTTP) Interface
    • 18.4 List of Supported Internet RFCs (Requests for Comment)
    • 18.5 IP Packet Processor Field Upgrade Procedure
      • 18.5.1 Overview
      • 18.5.2 Requirements for Field Upgrade
      • 18.5.3 Field Upgrade Procedure
  • Chapter 19. CARRIER ID (MetaCarrier®)
    • 19.1 Overview
    • 19.2 About MetaCarrier
    • 19.3 Functional Description
    • 19.4 Configure the CDM-625 for Carrier ID Operation
      • 19.4.1 Enable Carrier ID Operation
        • 19.4.1.1 Use the Front Panel Keypad and VFD to Enable Operation
        • 19.4.1.2 Use the Web Server (HTTP) Interface to Enable Operation
      • 19.4.2 Create the MetaCarrier Custom Message
        • 19.4.2.1 Use the Front Panel Keypad and VFD to Create the Message
        • 19.4.2.2 Use the Web Server (HTTP) Interface to Create the Message
  • Chapter 20. QUALITY of SERVICE (QoS)
    • 20.1 Overview
      • 20.1.1 QoS Terminology
    • 20.2 Layer 2 QoS
      • 20.2.1 Modem Tx Data Rate vs. QoS Tx Data Rate
      • 20.2.2 Flow Control
      • 20.2.3 Port-based Layer 2 QoS
      • 20.2.4 VLAN-based Layer 2 QoS
    • 20.3 Layer 3 QoS
      • 20.3.1 Layer 3 QoS Max-Pri Mode
      • 20.3.2 Layer 3 QoS Min-Max Mode
      • 20.3.3 Layer 3 QoS DiffServ Mode
        • 20.3.3.1 Layer 3 QoS Congestion Avoidance
        • 20.3.3.2 Layer 3 QoS List of Supported RFCs (Requests for Comment)
    • 20.4 QoS with ACM (Adaptive Coding and Modulation)
      • 20.4.1 Maximum Clipping
      • 20.4.2 Minimum Data Rate
  • Appendix A. CABLE DRAWINGS
    • A.1 Overview
      • A.1.1 EIA-530 to EIA-422/449 DCE Conversion Cable
      • A.1.2 EIA-530 to V.35 DCE Conversion Cable
      • A.1.3 EIA-232 Remote Control Cable
  • Appendix B. Eb/No MEASUREMENT
  • Appendix C. FAST ACTIVATION PROCEDURE
    • C.1 FAST System Overview
    • C.2 FAST Activation Procedure
      • C.2.1 FAST Activation via the CDM-625 Front Panel
      • C.2.2 FAST Activation via the CDM-625 Web Server (HTTP) Interface
  • Appendix D. REMOTE CONTROL
    • D.1 Overview
    • D.2 EIA-485
    • D.3 EIA-232
    • D.4 Basic Protocol
      • D.4.1 Packet Structure
        • D.4.1.1 Start of Packet
        • D.4.1.2 Target Address
        • D.4.1.3 Address Delimiter
        • D.4.1.4 Instruction Code
        • D.4.1.5 Instruction Code Qualifier
        • D.4.1.6 Optional Message Arguments
        • D.4.1.7 End Of Packet
    • D.5 Remote Commands and Queries
      • D.5.1 Table Indexes
      • D.5.2 Tx Parameters
      • D.5.3 Rx Parameters
      • D.5.4 Unit Parameters
      • D.5.5 Bulk Configuration Strings
      • D.5.6 Modem Information
      • D.5.7 Modem Performance Information
      • D.5.8 BUC Parameters (L-Band Device)
      • D.5.9 LNB Parameters (L-Band Device)
      • D.5.10 Ethernet Parameters
  • Appendix E. TELNET COMMAND LINE INTERFACE (CLI) OPERATION
    • E.1 Overview
      • E.1.1 Interface Access
      • E.1.2 Terminal Emulator Considerations
        • E.1.2.1 Using the PuTTY Terminal Emulator
        • E.1.2.2 Using the Tera Term Terminal Emulator
    • E.2 Using the Telnet Command Line Interface (CLI)
      • E.2.1 Telnet CLI Menu System – Parallel Functionality
      • E.2.2 CLI Menus – Common Navigation and Operation Features
    • E.3 Command Line Interface Pages
      • E.3.1 Home (Main) Menu
        • E.3.1.1 Home > Remote Access Mode
      • E.3.2 Home > Administration Submenu
        • E.3.2.1 Home > Administration > Host Access List
        • E.3.2.2 Home > Administration > SNMP
        • E.3.2.3 Home > Administration > Firmware (Base Modem) or (Packet Processor)
        • E.3.2.4 Home > Administration > Reboot
        • E.3.2.5 Home > Administration > FAST
        • E.3.2.6 Home > Administration > Save Modem Configuration / Load Modem Configuration
        • E.3.2.7 Home > Administration > Restore Factory Defaults
      • E.3.3 Home > Modem Submenu
        • E.3.3.1 Home > Modem > Interface
        • E.3.3.2 Home > Modem > Modem TX
        • E.3.3.3 Home > Modem > Modem RX
        • E.3.3.4 Home > Modem > Carrier-in-Carrier (CnC)
        • E.3.3.5 Home > Modem > Adaptive Coding and Modulation (ACM)
        • E.3.3.6 Home > Modem > Drop and Insert (D&I)
          • E.3.3.6.1 Home > Modem > Drop and Insert (D&I) > D&I Tables
        • E.3.3.7 Home > Modem > Block Upconverter (BUC)
        • E.3.3.8 Home > Modem > (Low-Noise Block Downconverter) LNB
        • E.3.3.9 Home > Modem > MEO (Medium-Earth Orbit)
        • E.3.3.10 Home > Modem > Utilities
        • E.3.3.11 Home > Modem > Overhead
      • E.3.4 Home > Network Submenu
        • E.3.4.1 Home > Network > Ethernet Ports
          • E.3.4.1.1 Home > Network > Ethernet Ports > Ethernet Port #
        • E.3.4.2 Home > Network > LAN IP
        • E.3.4.3 Home > Network > LAN ARP
          • E.3.4.3.1 Home > Network > LAN ARP > Arp Table > Arp Entry #
        • E.3.4.4 Home > Network > VLAN
          • E.3.4.4.1 Home > Network > VLAN > VLAN Table > VLAN #
        • E.3.4.5 Home > Network > Routes
          • E.3.4.5.1 Home > Network > Routes > Route Table
        • E.3.4.6 Home > Network > Managed Switch
        • E.3.4.7 Home > Network > IGMP (Internet Group Management Protocol)
        • E.3.4.8 Home > Network > DNS (Domain Name System)
        • E.3.4.9 Home > Network > DHCP (Dynamic Host Configuration Protocol)
        • E.3.4.10 Home > Network > PTP (Precision Time Protocol)
        • E.3.4.11 Home > Network > SNTP (Simple Network Time Protocol)
        • E.3.4.12 Home > Network > MAC Table
      • E.3.5 Home > WAN Submenu
        • E.3.5.1 Home > WAN > QoS Submenu
          • E.3.5.1.1 Home > WAN > QoS > Max-Pri and Min-Max Table
          • E.3.5.1.2 Home > WAN > QoS > QoS Differentiated Services Table
        • E.3.5.2 Home > WAN > Compression
        • E.3.5.3 Home >WAN > Encryption
      • E.3.6 Home > Outdoor Unit (ODU) Submenus (Summary Only)
      • E.3.7 Home > Redundancy Submenu
      • E.3.8 Home > General Information Submenu
        • E.3.8.1 Home > General Information > Modem Status
        • E.3.8.2 Home > General Information > Modem Information
        • E.3.8.3 Home > General Information > MAC Table
        • E.3.8.4 Home > General Information > Block Upconverter (BUC)
        • E.3.8.5 Home > General Information > Low Noise Block Downconverter (LNB)
      • E.3.9 Home > Logs Submenu
        • E.3.9.1 Home > Logs > Base Modem
          • E.3.9.1.1 Home > Logs > Base Modem > Stored Event Table
          • E.3.9.1.2 Home > Logs > Base Modem > Stored Statistic Table
        • E.3.9.2 Home > Logs > Packet Processor
          • E.3.9.2.1 Home > Logs > Packet Processor > Stored Event Table
      • E.3.10 Home > Statistics Submenu
        • E.3.10.1 Home > Statistics > Ethernet Submenu
          • E.3.10.1.1 Home > Statistics > Ethernet > Rx
          • E.3.10.1.2 Home > Statistics > Ethernet > Tx
          • E.3.10.1.3 Home > Statistics > Ethernet > Errors
        • E.3.10.2 Home > Statistics > Router
        • E.3.10.3 Home > Statistics > Managed Switch
        • E.3.10.4 Home > Statistics > WAN (Router Mode)
        • E.3.10.5 Home > Statistics > WAN (Managed Switch Mode)
        • E.3.10.6 Home > Statistics > Compression
          • E.3.10.6.1 Home > Statistics > Compression > Table View
        • E.3.10.7 Home > Statistics > QoS
          • E.3.10.7.1 Home > Statistics > QoS > Table View
        • E.3.10.8 Home > Statistics > PTP
          • E.3.10.8.1 Home > Statistics > PTP > LAN Details
          • E.3.10.8.2 Home > Statistics > PTP > WAN Details
        • E.3.10.9 Home > Statistics > CPU
        • E.3.10.10 Home > Statistics > Clear All Counters
      • E.3.11 Home > Contact Page
  • Appendix F. CDM-625 ODU (TRANSCEIVER, BUC, LNB) OPERATION
    • F.1 Overview
    • F.2 ODU Remote Control Address Setup
    • F.3 ODU Operations via the CDM-625 Front Panel
      • F.3.1 CDM-625 Front Panel Operation Overview
      • F.3.2 CDM-625 Front Panel Menus – ODU Menu Hierarchy
      • F.3.3 SELECT: (Main) Menu Overview
        • F.3.3.1 (SELECT: CONFIGURATION) Menu Branches
          • F.3.3.1.1 CONFIG: Tx ( Freq and CONFIG: Rx ( Freq Submenus
          • F.3.3.1.2 (SELECT: CONFIGURATION) Mask Submenus
            • F.3.3.1.2.1 CONFIG: Mask ( BUC
            • F.3.3.1.2.2 CONFIG: Mask ( LNB
        • F.3.3.2 (SELECT: MONITOR) Live-Alarms Menu
        • F.3.3.3 (SELECT:) ODU Menu Branches
          • F.3.3.3.1 ODU: BUC:PwrSupply+Ref (Power Supply and Reference)
            • F.3.3.3.1.1 ODU: BUC:PwrSupply+Ref ( PSU-and-10MHz Parameters
            • F.3.3.3.1.2 ODU: BUC:PwrSupply+Ref ( LO Freq (Local Oscillator Frequency)
            • F.3.3.3.1.3 ODU: BUC:PwrSupply+Ref ( PSUmonitor
          • F.3.3.3.2 ODU: LNB:PwrSupply+Ref (Power Supply and Reference)
            • F.3.3.3.2.1 ODU: LNB:PwrSupply+Ref ( PSU-and-10MHz
            • F.3.3.3.2.2 ODU: LNB:PwrSupply+Ref ( LO-Freq (Local Oscillator Frequency)
            • F.3.3.3.2.3 ODU: LNB:PwrSupply+Ref ( PSUmonitor
          • F.3.3.3.3 ODU: FSK-control
            • F.3.3.3.3.1 ODU: FSK-control ( CSAT
              • F.3.3.3.3.1.1 ODU: FSK-control ( CSAT (2CSATs ( CSAT #X) ( Configuration
                • F.3.3.3.3.1.1.1 ODU: FSK-control ( CSAT (2CSATs ( CSAT #X) ( Configuration ( Tx
                • F.3.3.3.3.1.1.2 ODU: FSK-control ( CSAT (2CSATs ( CSAT #X) ( Configuration ( Rx
                • F.3.3.3.3.1.1.3 ODU: FSK-control ( CSAT (2CSATs ( CSAT #X) ( Configuration ( LNA
                • F.3.3.3.3.1.1.4 ODU: FSK-control ( CSAT (2CSATs ( CSAT #X) ( Configuration ( Misc
              • F.3.3.3.3.1.2 ODU: FSK-control ( CSAT (2CSATs ( CSAT #X) ( Monitor
              • F.3.3.3.3.1.3 ODU: FSK-control ( CSAT (2CSATs ( CSAT #X) ( Alarms
                • F.3.3.3.3.1.3.1 ODU: FSK-control ( CSAT (2CSATs ( CSAT #X) ( Alarms (Current-Alarms
                • F.3.3.3.3.1.3.2 ODU: FSK-control ( CSAT (2CSATs ( CSAT #X) ( Alarms ( Stored-Alarms
              • F.3.3.3.3.1.4 ODU: FSK-control ( CSAT (2CSATs ( CSAT #X) ( Info
            • F.3.3.3.3.2 ODU: FSK-control ( 2CSATs
              • F.3.3.3.3.2.1 ODU: FSK-control ( 2CSATs ( CSAT#X
              • F.3.3.3.3.2.2 ODU: FSK-control ( 2CSATs ( Redundancy-Box
            • F.3.3.3.3.3 ODU: FSK-control ( KST
              • F.3.3.3.3.3.1 ODU: FSK-control ( KST ( Configuration
                • F.3.3.3.3.3.1.1 ODU: FSK-control ( KST ( Configuration ( Tx
                • F.3.3.3.3.3.1.2 ODU: FSK-control ( KST ( Configuration ( Rx
                • F.3.3.3.3.3.1.3 ODU: FSK-control ( KST ( Configuration ( Miscellaneous
                • F.3.3.3.3.3.1.4 ODU: FSK-control ( KST ( Information
                • F.3.3.3.3.3.1.5 ODU: FSK-control ( KST ( Information ( Model
                • F.3.3.3.3.3.1.6 ODU: FSK-control ( KST ( Information ( Tx+Rx-Param
                • F.3.3.3.3.3.1.7 ODU: FSK-control ( KST ( Information ( Misc
                • F.3.3.3.3.3.1.8 ODU: FSK-control ( KST ( Information ( Numbers
                • F.3.3.3.3.3.1.9 ODU: FSK-control ( KST ( Alarms
            • F.3.3.3.3.4 ODU: FSK-control ( BUC
              • F.3.3.3.3.4.1 ODU: FSK-control ( BUC ( Configuration
              • F.3.3.3.3.4.2 ODU: FSK-control ( BUC ( Status
              • F.3.3.3.3.4.3 ODU: FSK-control ( BUC ( Advanced-FSK
                • F.3.3.3.3.4.3.1 ODU: FSK-control ( BUC ( Advanced-FSK ( LPOD (2LPODs ( Online/Offline LPOD)
                  • F.3.3.3.3.4.3.1.1 ODU: FSK-control ( BUC ( Advanced-FSK ( LPOD (2LPODs ( Online/Offline LPOD) ( Cnfg
                  • F.3.3.3.3.4.3.1.2 ODU: FSK-control ( BUC ( Advanced-FSK ( LPOD (2LPODs ( Online/Offline LPOD)( Monitor
                  • F.3.3.3.3.4.3.1.3 ODU: FSK-control ( BUC ( Advanced-FSK ( LPOD (2LPODs( Online/Offline LPOD) ( LPOD ( Alarms
                  • F.3.3.3.3.4.3.1.4 ODU: FSK-control ( BUC ( Advanced-FSK ( LPOD (2LPODs( Online/Offline LPOD)( Statistics
                  • F.3.3.3.3.4.3.1.5 ODU: FSK-control ( BUC ( Advanced-FSK ( LPOD (2LPODs( Online/Offline LPOD)( Information
                  • F.3.3.3.3.4.3.1.6 ODU: FSK-control ( BUC ( Advanced-FSK ( LPOD (2LPODs( Online/Offline LPOD) ( Redun
                  • F.3.3.3.3.4.3.1.7 ODU: FSK-control ( BUC ( Advanced-FSK ( 2LPODs
    • F.4 ODU Operations via the CDM-625 Web Server (HTTP) Interface
      • F.4.1 Web Server Interface and Menu Tree
      • F.4.2 Web Page Descriptions
        • F.4.2.1 Configuration | BUC (Block Up Converter) Page
        • F.4.2.2 Configuration | LNB (Low Noise Block Down Converter)
        • F.4.2.3 Status | Modem Logs | Base Modem Page
        • F.4.2.4 ODU Pages
          • F.4.2.4.1 ODU | Enable
          • F.4.2.4.2 ODU | Config Pages
            • F.4.2.4.2.1 ODU | Config (CSAT-5060)
            • F.4.2.4.2.2 ODU | Config (KST-2000A/B)
          • F.4.2.4.3 ODU | Status
            • F.4.2.4.3.1 ODU | Status (CSAT-5060)
            • F.4.2.4.3.2 ODU | Status (KST-2000A/B)
          • F.4.2.4.4 ODU | Utilities
            • F.4.2.4.4.1 ODU | Utilities (CSAT-5060)
            • F.4.2.4.4.2 ODU | Utilities (KST-2000A/B)
    • F.5 ODU Operations via the CDM-625 Telnet Command Line Interface (CLI)
      • F.5.1 ODU Operations using the Telnet CLI
        • F.5.1.1 Home (Main) Menu
        • F.5.1.2 Home > Outdoor Unit (ODU) Submenu
          • F.5.1.2.1 Home > Outdoor Unit (ODU) > CSAT-5060 Submenu
            • F.5.1.2.1.1 Home > Outdoor Unit (ODU) > CSAT-5060 > Up Converter Settings 1/2, 2/2
            • F.5.1.2.1.2 Home > Outdoor Unit (ODU) > CSAT-5060 > Down Converter Settings 1/2, 2/2
            • F.5.1.2.1.3 Home > Outdoor Unit (ODU) > CSAT-5060 > Unit Settings 1/2, 2/2
            • F.5.1.2.1.4 Home > Outdoor Unit (ODU) > CSAT-5060 > LNA Settings
            • F.5.1.2.1.5 Home > Outdoor Unit (ODU) > CSAT-5060 > Status
            • F.5.1.2.1.6 Home > Outdoor Unit (ODU) > CSAT-5060 > Logs
            • F.5.1.2.1.7 Home > Outdoor Unit (ODU) > CSAT-5060 > Redundancy
            • F.5.1.2.1.8 Home > Outdoor Unit (ODU) > CSAT-5060 > Utilities
• BACK COVER