Marantz SR7300N - Manual (Page 40)

37
ENGLISH
3.
Each time the tuner finds a station, scanning will pause and the
station will be played for five seconds.
During this time, the following operations are possible.
1) The band can be changed by TUNER button .
2) The tuning mode can be changed by MODE button.
4.
If no button is pressed during this period, the current station is
memorized in location Preset 02
If you wish to skip the current station, press the TUNING
button
during this period, this station is skipped and auto presetting
continues.
5.
Operation stops automatically when all 50 preset memory
positions are filled or when auto scanning attains the highest end
of all bands. If you desire to stop the auto preset memory at
anytime, press the CLEAR button.
MANUAL PRESET MEMORY
(Using the SR7300)
1.
Tune into the radio station you desire (Refer to the “MANUAL
TUNING” or “AUTO TUNING” section).
2.
Press the MEMORY button on the front panel. “– –“ (preset
number) starts blinking on the display.
3.
Select the preset number by pressing the TUNING or button,
while this is still blinking (approx. 5 seconds)
4.
Press the MEMORY button again to enter. The display stops
blinking.
The station is now stored in the specified preset memory location.
(Using the remote control unit)
1.
Tune into the radio station you desire (Refer to the “MANUAL
TUNING” or “AUTO TUNING” section).
2.
Press the MEMO on the remote unite. “– –“ (preset number) starts
blinking on the display.
3.
Enter the desired preset number by pressing numeric buttons.
Note:
• When entering a single digit number (2 for example), either
input “02” or just input “2” and wait for a few seconds.
RECALLING A PRESET STATION
(Using the SR7300)
1.
Press the F/P button to show the preset station on the display.
2.
Select the desired preset station by pressing the TUNING or
button on the front panel
(Using the remote control unit)
1.
Press the 4 or ¢ button to select the desired preset station, or
input your desired preset channel with numeric buttons on the
remote.
PRESET SCAN
(Using the remote control unit)
1.
Press the P.SCAN on remote.
“PRESET SCAN” appears on the display and then the preset
station with the lowest preset number is recalled first.
2.
Preset stations are recalled in sequence (No.1 → No.2 → etc.) for
5 seconds each.
No stored preset number will be skipped.
3.
You can fast forward the preset stations by pressing the ¢
continuously.
When the desired preset station is received, cancel the preset
scan operation by pressing the CL button or P.SCAN on the
remote.
CLEARING STORED PRESET STATIONS
You can remove preset stations from memory using the following
procedure.
1.
Recall the preset number to be cleared with the method described
in “Recalling” a preset station.
2.
Press the MEMORY button on the front panel or press MEMO button
on the remote.
3.
Stored preset number blinks in the display for 5 seconds. While
blinking, press the CLEAR button on the front panel or press CL
button on the remote.
4.
“xx CLEAR” appears on the display to indicate that the specified
preset number has been cleared.
Notes:
• To clear stored all preset stations, press and hold the CLEAR
and the F/P buttons for two seconds.
AV SURROUND RECEIVER SR7300
SURROUND
MEMORY TUNING M F/P CLEAR
S-DIRECT MU A/D 7.1CH INPUT SPEAKRS A/B
POWER ON/STANDBY PHONES
ENTER
STANDBY DSS/VCR2 AUX1 AUX2 VCR1 DVD TV CD CD-R TAPE
SELECT
2. 4. 3.
3.
2.
MEMORY TUNING MODE F/P CLEAR
S-DIRECT MULTIROOM A/D 7.1CH INPUT SPEAKRS A/B
DSS/VCR2 AUX1 AUX2 VCR1 DVD TV CD CD-R TAPE TUNER
2. 1.
1.
1.
3.
1.
3.
3.
2.
AV SURROUND RECEIVER SR7300
SURROUND
MEMORY TUNING M F/P CLEAR
S-DIRECT MU A/D 7.1CH INPUT SPEAKRS A/B
POWER ON/STANDBY PHONES
ENTER
STANDBY DSS/VCR2 AUX1 AUX2 VCR1 DVD TV CD CD-R TAPE
SELECT
2. 3.