Ri-200 repeater controller system command list – Pacific Research Solutions RI-200 User Manual
Page 79
Pacific Research Solutions
RI-200 User Manual
Page 78
RI-200 REPEATER CONTROLLER SYSTEM COMMAND LIST
System
Command
System Command Description
and Data Format
Command
Syntax
Factory
Setting
Pwr on
Recover
50
Squelch adjust
Adj = 0 to 63 or * up one count, # down one count
50 [Adj]
31
Yes
51
Set squelch mode
Mode 0 = Normal, Mode 1 = SmartSquelch
51 [Mode]
1
Yes
52
Setup squelch
Item 1 = Upper threshold, Value = 75 to 200
Item 2 = Lower threshold, Value = 50 to 150
Item 3 = Acquisition time, Value = 0 to 50 in 10 ms increments
Item 4 = Delay factor, Value 0 to 255
Item 5 = Average factor, Value 0 to 50
Item 6 = Weak signal threshold, Value 3 to 50 in 10 ms inc.
52 [Item] [Value]
Item
1 = 160
2 = 130
3 = 8
4 = 125
5 = 25
6 = 5
Yes
53
Reserved
53 [ ]
N/A
N/A
54
Set Key code (prefix) for macros
Key = 0 to 4 digits (C and D are NOT VALID)
54 [Key]
0
Digits
Yes
55
Set Password for S-Cmd access
PW = 1 to 6 digits
55 [PW]
123456
Yes
56
Set Password for telephone incoming ring access
PW = 1 to 6 digits
56 [PW]
343
Yes
57
Set Password for telephone incoming control access
PW = 1 to 6 digits
57 [PW]
654381
Yes
58
Remote software reset
Controller Serial Number (SN) is 8 digits
58 [SN]
Serial
Number
N/A
59
Remote EEPROM initialize
Controller Serial Number (SN) is 8 digits
59 [SN]
Serial
Number
N/A
60
User telephone commands
Cmd # = 01 – 08, Group = 1 – 8
Line = 000 to 999, Name = 1 - 4 digits
60 [Cmd #]
[Group] [Line]
[Name]
See sec.
4.5 60
Yes
61
User S-Commands commands, call S-Command
Cmd # = 01 – 21, Group = 1 – 8
S-Cmd = 00 to 99, Name = 1 - 4 digits
61 [Cmd #]
[Group] [S-Cmd]
[Name]
See sec.
4.5.61
Yes
62
User commands
Cmd # = 01 – 08, Group = 1 – 8
Line = 000 to 999, Name = 1 to 4 digits
62 [Cmd #]
[Group] [Line]
[Name]
See sec.
4.5.62
Yes
63
Macro and message editor, set starting line number pointer
Line = 1 to 999
63 [Line]
N/A
N/A
64
Macro editor, insert an S-Command
S-Cmd/Data = 00 to 99 and its data as req. for the S-Cmd
No S-Cmd/Data for end of macro marker
64 [S-Cmd/Data]
See
Section
4.5.64
Yes
65
Reserved
N/A
N/A
66
Reserved
N/A
N/A
67
Reserved
N/A
N/A
68
Jump to macro line
Line = 1 – 999
68 [Line]
N/A
N/A
69
Exit system command mode
69
N/A
N/A