Teac RC-601MKII - Manual (Page 9)

TASCAM RC-601MKII
9
BASIC OPERATIONS
4 To check the playback sound, press the MONITOR key
to set the remote control unit to the monitor playback
mode. (The MONITOR key lights.)
z In addition to using an external monitor system, the
monitor playback sound can also be checked on
headphones connected to the PHONES terminal
on the CD-601MKII or the remote control unit. For
details when monitoring from the PHONES terminal
on the remote control unit, see “Headphone Monitor
Function” (page 25).
5 After checking the monitor playback sound, press the
READY key.
The disc returns to the tune start point, and the remote
control unit enters the online READY mode. (The
READY key lights.)
6 Press the ON LINE key to start online playback.
When the tune ends, playback automatically stops.
z To cancel playback, press the STOP key.
[NOTE]
• In the default setting, the failsafe function is ON, and
operation of keys other than STOP, PLAY MODE,
DISPLAY MODE and REPEAT is not accepted during
online playback. However, the menu system can be used
to set the failsafe function OFF. (→ page 25 “Failsafe
Function”)
Display of playback position
During playback, the approximate playback position in
the track is displayed on the character display area of the
display window in the form of a 12-dot bar. The number
of square dots in this bar increases the further playback
progresses. The following example shows that about 2/3 of
the track has been played back.
When the time display in the display window is the track
remaining mode (REMAIN), all of the square dots light
at the beginning of the track, and decrease as playback
progresses.
Playing from an Intermediate Point
in a Tune
To search for any intermediate point in a tune and play back
the final take from that point, select the track at step 3 in the
procedure “Playing a Specific Tune from the Beginning” on
the previous page, and perform the following.
4 Search for the desired point using the search (by using
the SEARCH dial), jog (by using the JOG/DATA dial) or
monitor playback (by using the MONITOR key) functions,
and set the remote control unit to the monitor PAUSE
mode. (→ page 12 “Searching for an Intermediate Point
in a Tune”)
5 Press the MONITOR key to perform monitor playback,
and check the point.
6 Press the READY key.
The disc returns to the point preset in step 4, and the CD
player enters the online READY mode. (The READY key
lights.)
To adjust the setting point, press the PAUSE key to enter
the monitor PAUSE mode, and return to step 4.
7 Press the ON LINE key to start playback. When the tune
ends, playback stops.
z To cancel playback, press the STOP key.
Auto-registering Cue Points
In the default setting, the position where monitor playback
was last started from the monitor PAUSE mode is
automatically registered as the cue point. When the READY
key is pressed during monitor playback, the CD-601MKII is
located to the cue point and enters the online READY mode.
By using menu item No. 20 (“CUE_SET”), you can select
either of the following two conditions as the condition for
auto-registering the cue point.
NOR (default setting): The position where monitor playback
was last started from the monitor PAUSE mode is
automatically registered as the cue point.
RDY: The position where monitor playback was started
from the monitor PAUSE mode, or the position where the
READY key was pressed from the monitor PAUSE mode is
auto-registered as the cue point.
z For details on menu operations, see “Menu Operations”
(page 13).
The auto-registered cue points above can be assigned to
numeric keys (CUE 1 to CUE 10) on the RC-601MKII. (→
page 21 “Functions using cue points”)
RC-601MKII_Eng.indd 9 3/24/2005 2:38:15 PM