Eneo EDC-3371 - Manual (Page 16)

6
TOUR SETUP
NUMBER : 0
TITLE : T0
SCAN TYPE : NORMAL
SPEED
: 5 STEP
DWELL : – – SEC
003 A08 – – – – – – – – – – – – – – –
– – – – – – – – – – – – – – – – – – – – –
– – – – – – P0 – – – – – – – – – – – –
– – – T0 – – – – – – – – – – – – – – –
– – – – – – – – – – – – – – – – – – – – –
– – – – – – – – – – – – – – – – – – – – –
SAVE AND EXIT (ESC TO CANCEL)
4.6 Shortcut of Preset Program
After selecting the desired scene, press No. ( 1 to 240), and press CTRL and PRST subsequently. The current view will be stored to the selected preset numb-
er if the preset number is empty. If selected preset number is not empty, „OVER WRITE” message will be displayed on the monitor and select the „OK” and
push the
Joystick to the right to overwrite.
Example: 1 , 0 , 1 + CTRL + PRST will store current view as preset No. 101. In this case, focus will be programmed as Auto, dwell time will be set to
3 seconds, and the current AE mode will be programmed.
4.7 Tour (Shortcut: TOUR)
There are 8 programmable Tours. Each Tour consists of up to 4 Preset positions, Patterns, Scans or other Tours (second-level). Using second-level tours, it
can be expanded to over 300 functions in a single tour.
– – –: blank position
SCAN TYPE: NORMAL/ VECTOR
SPEED:
 - 3 steps, the lower number means the slower speed.
DWELL: 03-99 sec
003: Preset (~40)
A08: Auto Scan (~8, 0 ~7)
P01: Pattern (~8)
T02: Tour (~8)
Follow the steps below to program the Tours:
. Press MENU to display the main menu on the monitor. Scroll to Tour and push the Joystick to the right to enter the TOUR menu. Or just press the TOUR
key on the keyboard.
. Select the” NUMBER” and set the desired number by pushing the Joystick left or right.
3. Choose a blank position to be programmed by pushing the Joystick up, down, right, or left.
4. To add a stored preset, twist the Joystick then the stored preset number displays.
5. To place functions other than preset, press TOUR, PTRN, or SCAN for Tour, Pattern or Auto Scan respectively.
6. You can also overwrite the programmed number and to remove a stored number from the Tour, press the HOME key on the stored number, a blank
position mark (– – –) will be displayed.
7. Repeat Step  through 5 for each desired position. Each title will be displayed on top of the line.
8. To edit the title, follow the procedure of the auto scan above to edit titles
9. Select Save and Exit and push the
Joystick to the right. Press ESC to exit the program without saving.
You can expand the tour sequence by calling other programmed tours.
NOTE: The speed applies in the vector mode only.
NOTE: In the Tour mode, in conjunction with preset and Auto Scan, you can make the camera travel from a preset position to another preset
position at a specific speed.
Example: Preset 00 > 00 > 003 > 004 > 005 > 006, Auto Scan 0 starts at preset 00, ends at preset 003, Auto Scan 0 starts at preset 005, ends at
preset 006; Tour 00, 00, A0, 004, A0.
 –>  ~3 –> 4 –> 5~6, repeat
where –> : Quick move, ~ : Programmed speed
To change the dwell time of the preset in the tour:
Use the
Joystick to move the cursor to a stored preset position. By pressing PRST key, the camera will move to the stored Preset view and the cursor moves
to the dwell time field.
After changing the dwell time, press
PRST key and the cursor moves to the preset number.
To assign the functions other than preset in the tour when the function key is not existed:
Use the
Joystick to move the cursor to a stored preset position. Pressing CTRL key or IRIS OPEN key will change the preset number to other function (AUTO
SCAN, PATTERN, TOUR, PRESET) with the first programmed number. To change the number, twist the joystick or press Tele or Wide key.