Silvercrest SDG 800 A1 - Manual (Page 51)

53 GB/MT
Initial Operation
points to the front towards the keypad and is
level. Thus, the turbo ring
8 will be kept in
position.
j  Place the food in the steam trays 3 , 4 , 6 .
j  Ensure that all parts are positioned correctly
before switching on the appliance.
AttEntIOn! Never use bowls or other parts,
not especially produced for this appliance.
Otherwise, there may be the risk of injuries
and / or damage of the appliance.
j  Now place the steam trays 3 , 4 , 6 in
1 - 2 - 3 succession (please see the markings on
the handles) on top of the condensate collection
basin
7 .
j  Place the cover 1 centrically so that the upper
steam tray 3 is completely closed and no
steam can exhaust.
j  Connect the mains plug 18 to a suitable socket.
j  The LC display 13 shows “45” (see Fig. B).
Now your steamer is ready for use.
Q   Setting the clock
Proceed as follows:
j  Simultaneously press the PROG 17 and ON /
OFF 14 buttons for 2 - 3 seconds. A signal tone
will be heard on releasing the buttons.
j  Press the PLUS button 16 to increase the time
indicator 20 by 10 minutes each time. Press the
MINUS button 16 to reduce the time indicator
20 by 1 minute each time.
j  Press the PROG button 17 to confirm your setting.
j  The LCD-display 13 will now show the current
clock time (clock time mode).
Q  
Using Immediate­Start Function
note: Consider that the base of the appliance /
water tank
10 has to be filled with water at least
up to the MIN mark 9 . Ensure that the turbo ring 8
in addition to the condensate collection basin 7
has been correctly positioned.
j  Press the ON / OFF button 14 . The LCD dis-
play 13 will show the factory-set steaming time
of 45 minutes (see fig. B).
j  Press the PLUS / MINUS button 16 to increase
the steaming time in 5-minute steps or decrease
it in 1-minute steps.
note: The maximum steaming time is 90 minutes.
note: Be aware that you might have to replen-
ish water when the steaming time is longer.
Use the openings on the sides of the conden-
sate collection basin
7 for refilling. If the base
of the appliance / water tank 10 is filled up to
the MAX mark 19 , it will be sufficient for approx.
1 hour of steaming.
AttEntIOn! HAzArD OF BUrnS!
Make sure that the water does not exceed the
MAX mark
19 . Otherwise, hot water may spurt
out of the steamer during operation.
j  Press the ON / OFF button 14 . The device sounds
a beep. The red indicator light 15 comes on
and the device starts the steaming process.
j  The LCD-display 13 will indicate the remaining
steaming time.
AttEntIOn! HAzArD OF BUrnS! The
appliance will become hot during use. Beware
of getting in contact with the ascending steam
or any components.
j  If the set steaming time is elapsed, the appli-
ance will automatically switch back to the
keep-warm mode (see “keep-warm mode”).
note: You can increase the steaming time at
any time in 5-minute steps or decrease it in
1-minute steps by pressing the PLUS / MINUS
button
16 . As soon as the steaming time is set
manually to “0”, the device switches automati-
cally into the warm mode (see “Warm mode”).
AttEntIOn! HAzArD OF BUrnS!
Always lift the cover
1 slowly, turning away
from you and let the steam exhaust backwards.
Do not bend over the appliance during steam
generation. Use oven cloths when touching the
cover
1 and the steam trays 3 , 4 , 6 . Use
a long fork or tongs when checking if the food
is done.
j  Press the ON / OFF button 14 to terminate the
steaming process prematurely or to switch off
58820_Dampfgarer_Content_LB5.indd 53 11.10.10 16:04