Document Outline

• aTCA-9710
• Revision History
• Table of Contents
• 1 Overview
  • 1.1 Introduction
  • 1.2 Block Diagram
  • 1.3 Package Contents
• 2 Specifications
  • 2.1 aTCA-9710 Specifications
    • 2.1.1 CPU/ Chipset/ Memory
    • 2.1.2 Standard and Interface
    • 2.1.3 Software
    • 2.1.4 Mechanical & Environmental
  • 2.2 Power Consumption
  • 2.3 Board Layout
    • 2.3.1 aTCA-9710 Board Layout - Component Side
    • 2.3.2 aTCA-9710 Board Layout - Solder Side
    • 2.3.3 aTCA-9710 Front Panel
    • 2.3.4 Status LED Definitions
  • 2.4 Compliance
• 3 Functional Description
  • 3.1 CPU, Memory and Chipset
    • 3.1.1 CPU
    • 3.1.2 Memory
    • 3.1.3 Intel® C612 Chipset Overview
    • 3.1.4 Silicon Motion SM750 Graphics Controller
  • 3.2 Peripherals
    • 3.2.1 Reset
    • 3.2.2 SMBus Devices
  • 3.3 I/O Interfaces
    • 3.3.1 USB
    • 3.3.2 VGA Interface
    • 3.3.3 Ethernet Connection
    • 3.3.4 Serial Port
    • 3.3.5 Onboard mSATA Module
    • 3.3.6 Switch And Jumper Settings
• 4 Intelligent Platform Management System
  • 4.1 IPMI Sensors
    • 4.1.1 Sensor Reading (FRU Hotswap Sensor)
    • 4.1.2 Get Sensor Reading (Physical IPMB-0 Sensor)
    • 4.1.3 Watchdog Timer Sensor
    • 4.1.4 Version Change Sensor
    • 4.1.5 System Firmware Progress Sensor
    • 4.1.6 Get Sensor Reading Command
  • 4.2 IPMI Commands
• 5 Getting Started
  • 5.1 Safety Requirements
  • 5.2 Installing and Removing the aTCA-9710
    • 5.2.1 Installing the Blade
    • 5.2.2 Removing the Blade
  • 5.3 Firmware Update Procedure
    • 5.3.1 Update Over Serial Interface
    • 5.3.2 Update over KCS
    • 5.3.3 Update over LAN
• 6 BIOS
  • 6.1 Entering the BIOS Setup Screen
    • 6.1.1 Navigation
  • 6.2 Main BIOS Setup Screen
  • 6.3 Advanced Setup Screen
    • 6.3.1 ACPI Settings
    • 6.3.2 NCT5104D Super IO Configuration
    • 6.3.3 Serial Port Console Redirection
    • 6.3.4 PCI Subsystem Settings
    • 6.3.5 Network Stack Configuration
    • 6.3.6 CSM Configuration
    • 6.3.7 Trusted Computing
    • 6.3.8 ADLINK IPMI settings
  • 6.4 Intel RC Setup
    • 6.4.1 Processor Configuration
    • 6.4.2 Advanced Power Management Configuration
    • 6.4.3 Common RefCode Configuration
    • 6.4.4 Memory Configuration
    • 6.4.5 IIO Configuration
    • 6.4.6 PCH Configuration
  • 6.5 Server Mgmt Setup Screen
  • 6.6 Boot Setup Screen
  • 6.7 Security Setup Screen
  • 6.8 Save & Exit Setup Screen
• 7 Serial Over LAN
  • 7.1 Preparation For SOL Connection
  • 7.2 Configure The Remote Client
    • 7.2.1 Install IPMItool For The Remote Client
  • 7.3 Configure The Target aTCA-9710
    • 7.3.1 BIOS Configuration
    • 7.3.2 Linux grub Setting
    • 7.3.3 Linux System Setting
  • 7.4 Establish SOL Connection
• 8 Drivers
• Safety Instructions
• Getting Service