Document Outline

• Table of contents
• 1 Basic structure
• 2 Safety information and use
  • 2.1 Requirements for the user
  • 2.2 Scope of application
    • 2.2.1 Operating principle
    • 2.2.2 Drive motor and speed regulation
  • 2.3 Obligations of the operator
  • 2.4 Information on hazards and symbols used in this manual
  • 2.5 Device safety information
  • 2.6 Protective equipment
    • 2.6.1 Opening the hood without mains connection
    • 2.6.2 Imbalance switch
  • 2.7 Hazardous points
  • 2.8 Electrical safety
    • 2.8.1 General information
    • 2.8.2 Protection against restart
    • 2.8.3 Overload protection
    • 2.8.4 Imbalance detection
    • 2.8.5 Operation on GFCI (Ground-Fault Circuit Interrupters)
• 3 Technical data
  • 3.1 Dimensions
  • 3.2 Weight
  • 3.3 Operating noise
  • 3.4 Voltage
  • 3.5 Current consumption
  • 3.6 Power consumption
  • 3.7 Electrical fuses
  • 3.8 Material
  • 3.9 Final fineness
• 4 Installation
  • 4.1 Transport
  • 4.2 Unpacking
  • 4.3 Setting up
  • 4.4 Ambient conditions
  • 4.5 Electrical connection
    • 4.5.1 Adjusting the mains voltage
      • 4.5.1.1 Adjusting the mains voltage with the rotary switch (8)
      • 4.5.1.2 Adjusting the mains voltage in setup mode
  • 4.6 Setting device specification in setup mode
• 5 Initial start-up
  • 5.1 Switching on
  • 5.2 Function check
• 6 Using the device
  • 6.1 Choice of grinding bowls and grinding balls
    • 6.1.1 Size of the grinding balls
    • 6.1.2 Number of balls per grinding bowl (independent of the material quantity)
    • 6.1.3 Calculated weight of a ball
  • 6.2 Filling quantities of grinding bowls
  • 6.3 Filling the grinding bowl
  • 6.4 Factors with an impact on grinding
    • 6.4.1 Running time (grinding duration)
    • 6.4.2 Speed
    • 6.4.3 Reverse mode
    • 6.4.4 Number and size of the balls
    • 6.4.5 Weight of the balls (type of material)
    • 6.4.6 Dry grinding
    • 6.4.7 Wet grinding (grinding in a suspension)
  • 6.5 Clamping the grinding bowls
    • 6.5.1 Clamping with the "Safe-Lock" (5) tensioning device
    • 6.5.2 Clamping the 80 ml grinding bowls
  • 6.6 Mass balance
  • 6.7 Grinding duration
  • 6.8 Settings on the control panel
    • 6.8.1 Setting the speed
    • 6.8.2 Setting the running time
      • 6.8.2.1 Changing the time unit in setup mode
  • 6.9 Repetition of grinding / pause cycles
  • 6.10 Reverse mode
  • 6.11 Conducting a grinding operation
    • 6.11.1 Overload
    • 6.11.2 Switching off
  • 6.12 Cooling the grinding bowl
  • 6.13 Stand-by
• 7 Accessories
  • 7.1 Additional clamping system for grinding harmful substances or in a gas atmosphere.
    • 7.1.1 Locking the additional clamping system into place
  • 7.2 Grinding in inert gas with gassing lid
    • 7.2.1 Preparation for gassing
    • 7.2.2 Gassing
    • 7.2.3 Ventilate after grinding
    • 7.2.4 Cleaning the valves
    • 7.2.5 Installing valve inserts
  • 7.3 GTM - system
• 8 Cleaning
  • 8.1 Grinding elements
  • 8.2 Mill
• 9 Maintenance
• 10 Repairs
  • 10.1 Checklist for troubleshooting
• 11 Examples of comminution tasks
• 12 Disposal
• 13 Guarantee terms
• 14 Exclusion of liability
• 15 Safety logbook
• 16 Index