Document Outline

• 2080-UM001D-EN-E Micro810 Programmable Controllers User Manual
  • Preface
    • Who Should Use this Manual
    • Purpose of this Manual
    • Additional Resources
  • 1 - Hardware Overview
    • Hardware Features
      • Micro810 12-Point Controllers
  • 2 - About Your Controller
    • Programming Software for Micro800 Controllers
      • Obtain Connected Components Workbench
      • Use Connected Components Workbench
    • Agency Certifications
    • Compliance to European Union Directives
      • EMC Directive
      • Low Voltage Directive
    • Installation Considerations
      • Environment and Enclosure
      • Preventing Electrostatic Discharge
    • Safety Considerations
      • North American Hazardous Location Approval
      • Disconnecting Main Power
      • Safety Circuits
      • Power Distribution
      • Periodic Tests of Master Control Relay Circuit
    • Power Considerations
      • Isolation Transformers
      • Power Supply Inrush
      • Loss of Power Source
      • Input States on Power Down
      • Other Types of Line Conditions
    • Preventing Excessive Heat
    • Master Control Relay
      • Using Emergency-Stop Switches
      • Schematic (Using IEC Symbols)
      • Schematic (Using ANSI/CSA Symbols)
  • 3 - Install Your Controller
    • Controller Mounting Dimensions
      • Mounting Dimensions
      • Module Spacing
      • DIN Rail Mounting
      • Panel Mounting
  • 4 - Wire Your Controller
    • Wiring Requirements
    • Use Surge Suppressors
      • Recommended Surge Suppressors
    • Ground the Controller
    • Wiring Diagrams
      • Micro810 Controllers
    • Controller I/O Wiring
      • Minimize Electrical Noise
      • Analog Channel Wiring Guidelines
      • Minimize Electrical Noise on Analog Channels
      • Ground Your Analog Cable
      • Wiring Examples
  • 5 - Troubleshooting
    • Status Indicators on the Controller
      • Micro810 Controllers
    • Status Indicators on the LCD Module
    • Error codes
    • Controller Error Recovery Model
    • Calling Rockwell Automation for Assistance
  • 6 - Program Execution in Micro800
    • Configure and Program Your Micro810 Controller
    • Overview of Program Execution
      • Execution Rules
      • Power Up and First Scan
      • Periodic Execution of Programs
    • Memory Allocation
    • Guidelines and Limitations
  • 7 - Controller Security
    • Exclusive Access
    • Password Protection
    • Compatibility
      • Connected Components Workbench revision 1 with Micro800 controller firmware revision 2
      • Connected Components Workbench revision 2 with Micro800 controller firmware revision 1
    • Work with a Locked Controller
      • Upload from a Password-Protected Controller
      • Debug a Password-Protected Controller
      • Download to a Password-Protected Controller
      • Transfer Controller Program and Lock Receiving Controller
      • Back Up a Password-Protected Controller
    • Configure Controller Password
    • Recover from a Lost Password
  • A - Specifications
    • Micro810 Controllers
      • Micro800 Programmable Controller External AC Power Supply
  • B - About Accessories
    • Accessories
      • External AC Power Supply
        • Wire the Module
      • 1.5" LCD Display and Keypad Module
        • Insert the LCD Module
        • Remove the LCD Module
        • Access the Main Menu
      • USB Adapter
  • C - Quickstarts
    • Configure LCD Password
      • Activate Password
      • Deactivate Password
      • Change Password
      • Delete Password
    • Configure Controller Password
      • Set Controller Password
      • Change Password
      • Clear Password
    • Use the Micro810 Smart Relay Functionality
      • Smart Relay Block Execution Order
      • Navigate the LCD Display
      • Configure Count-Up (CTU)
      • Test the CTU Predefined Function
      • Configure On-delay Timing (TON)
      • Test the TON Predefined Function
      • Configure DOY
      • Test the DOY Predefined Function
        • Set up the Clock for Testing
        • Test the DOY Function
      • Configure TOW
      • Test the TOW Predefined Function
        • Set up the Clock for Testing
        • Test the TOW Function
      • Configure Countdown (CTD)
      • Test the CTD Predefined Function
      • Configure TONOFF
      • Test the TONOFF Predefined Function
      • Configure Pulse Timing (TP)
      • Test the TP Predefined Function
      • Configure TOF
      • Test the TOF Predefined Function
    • Flash Update the Micro800 Firmware
    • Establish Communication Between RSLinx and a Micro810 12-point controller through USB
    • Forcing I/O
      • Check if Forces (locks) are Enabled
      • I/O Forces After a Power Cycle
  • D - IPID Function Block
    • How to AutoTune
    • PID Application Example
      • IPID Autotuning for First and Second Order Systems
    • PID Code Sample
  • Index
• Back Cover