Document Outline

• Cover
• Contents
• Overview
  • System Diagram
  • Parts List
  • Safety
• Introduction
  • Specifications
    • Analog Inputs
    • Digital Inputs
    • User-Selectable Digital Outputs
    • System Digital Outputs
    • Analog Outputs
  • Miscellaneous Specifications
    • Physical Dimensions
• Installation
  • Precautions and Warnings
  • Recommended Tools
    • Panel Hole Cutters
    • Other Tools
  • CLS Mounting Procedure
    • Mounting Environment
    • Steps
  • TB-18 Mounting Instructions
  • TB-50 Mounting Instructions
  • General Wiring Recommendations
    • Grounding
    • Thermocouple Wiring
    • Input Wiring
    • Output Wiring
    • Communications Wiring
  • Wiring: Noise Suppression
  • General Wiring
    • Power Wiring and Controller Test
  • Outputs
    • PID Control and Alarm Output Connections
    • Watchdog Timer
    • TB-18
    • TB-50
  • Inputs
    • Input Scaling
    • 4 and 8 CLS Scaling Values
    • 16 CLS Scaling Values
    • Scaling and Calibration
    • T/C Inputs
    • RTD Inputs (4 and 8 CLS only)
    • Current Inputs
    • Voltage Inputs
    • Unused Inputs
    • Back Terminal Block Connections
  • Serial Communications
    • RS-232 Interface
    • RS-485 Interface
• Using the CLS
  • Introduction
  • Front Panel
    • Front Panel Keys
  • Displays
    • Bar Graph Display
    • Single Loop Display
    • Alarms
  • Job Display
  • Operator Menus
    • Change Setpoint
    • Manual/Automatic Control
    • Ramp/Soak
• Setup
  • How to Enter the Setup Menus?
  • How to Edit a Menu?
  • Set up Global Parameters Menu
    • Load a Job
    • Save Setup to Job
    • Job Select Inputs
    • Job Select Input Polarity
    • Output Override Digital Input
    • Output Override Input Polarity
    • Start-up Alarm Delay
    • Keyboard Lock Status
    • Power-Up Output Status
    • Controller Address
    • Communications Baud Rate
    • Communications Protocol
    • Communications Error Checking
    • AC Line Frequency
    • Digital Output Polarity
    • EPROM Information
  • Set up Loop Input
    • Input Type
    • Pulse Sample Time
    • Loop Name
    • Input Units
    • Input Reading Offset
    • Linear Scaling Menus
    • Display Format
    • High Process Value
    • High Reading
    • Low Process Value
    • Low Reading
    • Input Filter
  • Set up Loop Control Parameters
    • Heat or Cool Control PB
    • Heat or Cool Control TI
    • Heat or Cool Control TD
    • Heat or Cool Output Filter
    • Heat or Cool Spread
  • Set up Loop Outputs
    • Enable/Disable Heat or Cool Outputs
    • Heat or Cool Output Type
    • Heat or Cool Cycle Time
    • SDAC Menus
      • SDAC Mode
      • SDAC High Value
      • SDAC Low Value
    • Heat or Cool Output Action
    • Heat or Cool Output Limit
    • Heat or Cool Output Limit Time
    • Heat or Cool Output Override
    • Heat or Cool Nonlinear Output Curve
  • Set up Loop Alarms
    • Alarm Types
    • High Process Alarm Setpoint
    • High Process Alarm Type
    • High Process Alarm Output Number
    • Deviation Band Value
    • High Deviation Alarm Type
    • High Deviation Alarm Output Number
    • Low Deviation Alarm Type
    • Low Deviation Alarm Output Number
    • Low Process Alarm Setpoint
    • Low Process Alarm Type
    • Low Process Alarm Output Number
    • Alarm Deadband
    • Alarm Delay
  • Manual I/O Test
    • Digital Input Testing
    • Test Digital Output
    • Toggle Digital Output
    • Keypad Test
• PID Tuning and Control
  • Introduction
  • Control Modes
    • On/Off Control
    • Proportional Control
    • Proportional and Integral Control
    • Proportional, Integral and Derivative Control
    • Control Outputs
    • Digital Output Control Forms
  • Setting Up and Tuning PID Loops
    • Proportional Band (PB) Settings
    • Integral Term (TI) Settings
    • Derivative Term (TD) Settings
  • General PID Constants by Application
    • Proportional Band Only (P)
    • Proportional wth Integral (PI)
    • PI with Derivative (PID)
• Troubleshooting
  • No Key Reset
  • Returning Your Unit
  • Troubleshooting Stand-Alone Systems
    • Checking an Analog Input
    • Checking Digital I/O
  • Checking Computer Supervised Systems
    • Computer Problems
    • Software Problems
    • Changing the EPROM
• Linear Scaling Examples
  • Example 1
  • Example 2
  • Example 3
• Appendix A: Ramp Soak
  • Introduction
    • R/S Features
    • Specifications
  • Configuring Ramp/Soak
    • Setting the R/S Time Base
    • Editing R/S Parameters
    • Choosing a Profile to Edit
    • Copying the Setup from Another Profile
    • Editing the Tolerance Alarm Time
    • Editing the Ready Setpoint
    • Editing the Ready Event States
    • Choosing and External Reset Input
    • Editing a Segment
    • Setting Segment Time
    • Setting a Segment Setpoint
    • Configuring Segment Events
    • Editing Event Outputs
    • Changing Event States
    • Editing Segment Triggers
    • Assigning an Input to a Trigger
    • Changing a Trigger's True State
    • Latching or Unlatching a Trigger
    • Setting Segment Tolerance
    • Ending a Profile
    • Repeating a Profile
  • Using Ramp/Soak
    • Assigning a Profile to a Loop
    • Assigning a Profile to a Linear Input Loop
    • Running a Profile
    • Ramp/Soak Displays
    • Holding a Profile or Continuing from Hold
    • Resetting a Profile
• Appendix B: Enhanced Process Control
  • Enhanced Process Control Menus
  • Process Variable Retransmit
    • Setting Up a PV Retransmit
    • PV Retransmit Menus
  • Cascade Control
    • Setting Up Cascade Control
    • Cascade Control Menus
  • Ratio Control
    • Setting Up Ratio Control
    • Ratio Control Menus
  • Remote Analog Setpoint
  • Differential Control
  • Typical Applications
    • Process Variable Retransmit
    • Cascade Control
    • Ratio Control
    • Remote Setpoint
    • Differential Control
• Glossary