Document Outline

• Contents
• Introduction
  • Indications for use
  • Contraindications
• Symbols
  • Documentation symbols
  • Power symbols
  • Connectivity symbols
  • Miscellaneous symbols
• Screen elements
• About warnings and cautions
  • General warnings and cautions
• Physical design
  • Controls, indicators, and connectors
• Setup
  • Supplies and accessories
  • Insert the battery
  • Mount the monitor
    • Check the mounting bracket
    • Mount the monitor on a stand
    • Mount the monitor on the wall
  • Attach the probe well
  • Attach the temperature probe
  • Remove the temperature probe and well
  • Connect the NIBP hose
  • Disconnect the NIBP hose
  • Connect the SpO2 cable or the SpO2/RRa dual cable
  • Disconnect the SpO2 cable or the SpO2/RRa dual cable
  • Connect the patient movement cable
  • Disconnect the patient movement sensor and cable
  • Attach a USB accessory
  • Detach a USB accessory
  • Insert a new roll of paper
  • Connect AC power
  • Disconnect AC power
• Startup
  • Power
    • Power on/Display power-saving button
  • Power up the monitor
  • Power down the monitor
  • Reset the monitor
  • Set the date and time
  • Enter clinician information
  • Set the default configuration
• Navigation
  • Home tab
  • Device Status area
    • Battery status
    • Alarm and information messages
  • Content area
  • Navigation area
    • Display lock
      • Lock the display
      • Unlock the display
• Using the keypad, keyboard, and barcode scanner
  • Open the numeric keypad
  • Numeric keypad
  • Enter a number
  • Close the numeric keypad
  • Open the keyboard
  • Keyboard
  • Enter a letter or number
  • Enter a symbol or special character
  • Enter a diacritical mark
  • Close the keyboard
  • Use a barcode scanner
• Connex CS
  • Overview
  • Monitor tab
  • Connect to the central station
  • Disconnect from the central station
  • Continuous patient monitoring
  • Activate the Continuous Monitoring profile
  • Pause continuous monitoring (Pause mode)
  • Resume continuous monitoring
    • Pause time remaining
    • Pause time limit expired (patient sensors connected)
    • Pause time limit expired (patient sensors disconnected)
  • End continuous monitoring
  • Assign a patient and location
• Profiles
  • Continuous Monitoring profile
  • Continuous Monitoring profile
  • Saving vital sign measurements (Continuous Monitoring profile)
  • Intervals Monitoring profile
  • Spot Check profile
  • Triage profile
  • Profile feature comparison
  • Profile feature comparison
  • Changing profiles
    • Change from one non-continuous profile to another non-continuous profile
    • Change to the Continuous Monitoring profile
    • Change from the Continuous Monitoring profile
• Patient data management
  • Add a patient to the patient list
  • Load patient data with a barcode scanner
  • Select a patient
  • Manage patient records (Continuous Monitoring profile)
  • Manage patient records (Intervals Monitoring, Spot Check, and Triage profiles)
  • Printer
  • Delete a patient from the list
• Alarms
  • Alarm types
  • Icons on the Home tab
  • Patient rest mode
    • Patient rest mode location on the monitor
    • Turn on patient rest mode
    • Turn off patient rest mode
  • Reset (pause or turn off) audio alarms
  • Cancel a paused alarm
  • Adjust vital sign alarm limits
  • Modify audio alarm notification
  • Alarm messages and priorities
    • Physiological alarms
    • Technical alarms
    • Technical alarms
  • Nurse call
• Patient monitoring
  • Standard and custom modifiers
    • Enter modifiers
  • Custom scoring
  • Manual overrides
    • Enter a manual override measurement
  • Patient movement
    • Movement frame
      • Exit alarm view
      • Set up movement
      • Configure movement alarms and patient turn reminder
      • Monitor patient movement
      • Low confidence condition
      • Observe and report patient turn events
  • Capnography (CO2)
    • etCO2 frame
      • etCO2 numeric view
      • CO2 waveform view
      • Set up etCO2
      • Configure etCO2 and FiCO2 alarms
      • Measure CO2
      • Stop and restart the CO2 pump
      • Stop and restart the CO2 pump
  • Respiration rate
    • RR frame
      • Set up RR
      • Configure RR alarms
  • IPI
    • IPI frame
      • IPI numeric view
      • IPI trend graph view
      • Set up IPI
      • Configure IPI alarms
  • Acoustic respiration rate (RRa)
    • RRa frame
      • Respiration Indicator
      • Averaging selector
    • Set up RRa
    • Configure RRa alarms
    • Measure RRa
  • NIBP
    • Noninvasive Blood Pressure (NIBP) frame
      • NIBP frame in Continuous Monitoring profile
      • NIBP frame in Intervals Monitoring profile
      • NIBP frame in Spot Check and Triage profiles
      • NIBP measurement display
      • View indicator
      • Buttons
    • Select a cuff
      • Cuff measurements
    • Position the cuff
    • Set up NIBP
    • Configure NIBP alarms
    • NIBP measurement
      • Take a manual NIBP measurement
      • Cancel a measurement that is in progress
      • Interval NIBP measurement
  • Temperature
    • Temperature frame
      • Temperature frame in Continuous Monitoring profile
      • Temperature frame in Intervals Monitoring profile
      • Temperature frame in Spot Check and Triage profiles
      • Temperature measurement display
      • Site selection
      • Temperature buttons
    • Set up temperature
    • Configure temperature alarms
    • SureTemp® Plus temperature module
      • Temperature mode selection
      • Take a temperature in the Predictive mode
      • Take a temperature in the Direct mode
      • Take a temperature at the rectal site
    • Braun ThermoScan® PRO 4000 thermometer and accessory dock
      • Take a temperature at the ear site
      • Change the temperature scale on the ear thermometer
      • Charge the ear thermometer battery
  • SpO2
    • SpO2 frame
      • SpO2 numeric view
      • SpO2 waveform view
    • Set up SpO2
    • Configure SpO2 alarms
    • Set Response Mode
    • Measure SpO2 and pulse rate
  • SpHb
    • SpHb frame
      • SpHb numeric view
      • SpHb graphical trend view
    • Set up SpHb
    • Configure SpHb alarms
    • Set SpHb averaging mode
    • Measure SpHb
  • Pulse rate frame
    • Continuous Monitoring profile
    • Intervals Monitoring profile
    • Spot Check and Triage profiles
    • Set up pulse rate
    • Configure pulse rate alarms
  • Manual parameters frame
    • Enter manual parameters
• Maintenance and service
  • Perform periodic checks
  • Replace the printer paper
  • Change the battery
  • Clean the monitor
    • 70 percent isopropyl alcohol
    • 10 percent chlorine bleach solution
  • Clean the accessories
  • Clean the stand
• Advanced settings
  • General
    • Specify the language
    • Specify date and time settings
    • Specify advanced alarm settings
    • Specify advanced display settings
    • Specify advanced device settings
    • Set and start the demo mode
  • Parameters
    • Specify advanced IPI settings
    • Specify advanced RRa settings
    • Specify advanced SpO2 settings
    • Specify advanced pulse rate settings
    • Specify advanced etCO2 settings
    • Specify advanced SpHb settings
    • Specify advanced NIBP settings
    • Specify advanced temperature settings
    • Specify the manual parameters
  • Data management
    • Specify patient settings
    • Specify clinician settings
    • Specify clinical data settings
  • Network
    • View advanced monitor information
    • Specify radio settings
    • Specify server settings
  • Service
• Troubleshooting
  • Patient movement messages
  • CO2 messages
  • RRa messages
  • NIBP messages
  • SpO2 and SpHb messages
  • Temperature messages
  • Weight scale messages
  • Patient data management messages
  • Communications module messages
  • Radio messages
  • Ethernet messages
  • USB and USB flash drive messages
  • System messages
  • Battery power manager messages
  • Configuration Manager messages
  • Printer messages
  • Network messages
  • Problems and solutions
• Specifications
  • Physical specifications
  • Physical specifications
  • Environmental specifications
  • Monitor radio
  • Configuration options
• Standards and compliance
  • General compliance and standards
  • General radio compliance
    • Federal Communications Commission (FCC)
    • Industry Canada (IC) emissions
    • European Union
• Guidance and manufacturer's declaration
  • EMC compliance
  • Emissions and immunity information
• Appendix
  • Approved accessories
    • FlexiPort cuffs (not made with natural rubber latex)
    • Blood pressure accessories (not made with natural rubber latex)
    • Masimo pulse oximetry (for use with devices with SpO2)
    • Masimo rainbow set (for use with devices with SpO2 and SpHb)
    • Masimo RRa
    • Nellcor pulse oximetry
    • SureTemp Plus thermometry
    • Braun ThermoScan PRO 4000 thermometer and accessory dock
    • EarlySense RR, pulse rate, and patient movement
    • Oridion CO2
    • Mounting options
    • Weight scales and connectivity kits
    • Miscellaneous items
    • Service
    • Literature/Documentation
  • Warranty