Integra DTR-6.4/5.4 - Manual (Page 34)

34
Selecting the appropriate setting for your connection
DTR-5.4
This setting allows you to set the crossover frequency for your
speaker system. The crossover frequency is the minimum frequency
delivered to a speaker and can be set to 60 Hz, 80 Hz, 100 Hz, 120
Hz, or 150Hz. This setting is valid when “Subwoofer” is set to
“Yes,” or for speakers that are set to “Small,” at the “Speaker
Config” menu. Frequencies below this are cut from speakers set to
“Small” and sent to the subwoofer (or to speakers set to “Large”).
The following table lists the crossover frequency you should choose
depending on the diameter of your front spekers.
Note:
When “Large” is set, the complete frequency range for that speaker
channel will be output. When “Small” is set, the frequencies below
80 Hz for that speaker channel are output to the subwoofer. If
Subwoofer is set to “No” in the 1-1. Speaker Config Sub-menu,
then they will be output to the left and right front speakers.
When the default input settings does not suit your connection,
perform the following procedures to configure your input settings.
a. Digital Input
This setting tells the DTR-6.4/5.4 which input source button on the
front panel is connected with which digital input jack on the rear
panel.
The default settings are given below.
----: Available for digital input but not set in initial settings.
Notes:
• When you select “Tuner” for input, you cannot assign digital
input to “Tuner.”
• Since Video 4 is fixed to the optical digital terminal on the front
panel, this item will be disabled if Video 4 is selected.
For example, if the input source selected at the front panel is CD
and the compact disc player is connected to DIGITAL IN
OPTICAL 2, then select “OPT2” here. If the input source selected
is not connected to a digital input, then select “----.”
b. Component Video
Use this setting if you connect monitors like TV to the COMPONENT
VIDEO OUTPUT jacks on the DTR-6.4/5.4.
Front speaker diameter crosscover frequency
Larger than 8" (20 cm) 60
6-1/2"~8" (16-20 cm) 80
5-1/4"~6-1/2" (13-16 cm) 100
3-1/2"~5-1/4" (9-13 cm) 120
Less than 3-1/2" (9 cm) 150
Configuring the input settings suitable for your
connection
Input source Digital input
CD COAX
Phono (DTR-6.4 only) ----
Tape ----
DVD OPT 1
Video 1 ----
Video 2 ----
Video 3 OPT 2
The default settings are given below.
For example, when you connect the DVD player to the
COMPONENT VIDEO INPUT 2 jacks, select “DVD” as input
source and set “b. Component Video” to “INPUT 2.”
INPUT 1: Selects when the video device is connected to the
COMPONENT VIDEO INPUT 1 jacks.
INPUT 2: Selects when the video device is connected to the
COMPONENT VIDEO INPUT 2 jacks.
Video (DTR-6.4 USA and Canadian models only): Selects
when you want to output the video signal which comes in from
the device connected to the VIDEO or S VIDEO terminals
through the COMPONENT VIDEO OUTPUT terminals.
Last: Select to have the video of the previous input source
continued.
Note:
CD, Phono (DTR-6.4 only), Tuner and Tape are fixed to “Last.”
h. Trigger A, i. Trigger B
This menu allows you to make the required settings to turn on the
output from the 12V TRIGGER terminal to control another
component or device with the DTR-6.4/5.4 for each input source.
On: Select to activate the device connected to the 12V TRIGGER A
(or B) terminal when the input source is selected.
Off: Select when no device is connected to the 12V TRIGGER A
(or B) terminal or you do not want the connected device to activate.
Setup Procedure
1. Select the desired input source.
2. Display the main menu.
Press the Setup button on the front panel or Setup button on the
remote controller to display the main menu on the monitor and
front display.
Input source selected Component video input
DVD INPUT 1
Video 1 INPUT 2
Video 2 INPUT 2
Video 3 INPUT 2
Video 4 INPUT 2
* Menu *****************
1.Hardware Config
2.Speaker Config
3.Speaker Distance
4.Level Calibration
5.Input Setup
6.Preference
|ENTER|Quit:|SETUP|